Question about 2003 Ford Ranger Regular Cab

Open Question

How do i remove a fan clutch on a 2003 Ford Ranger 2.3L?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: need clutch replacement directions for Ford Ranger

Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Posted on Apr 19, 2009

mcgyver468
  • 710 Answers

SOURCE: How to remove fan clutch on 94 Ranger 4.0?

THERE IS A SPECIAL TOOL THAT CAN BE RENTED OR PURCHASED AT YOUR LOCAL AUTO PARTS STORE. IT CONSISTS OF A LARGE OPEN END WRENCH AND A LONG FORK-LIKE TOOL THAT GRABS THE NUTS ON THE FAN SO THAT THE WRENCH CAN LOOSEN THE LARGE NUT THAT HOLDS THE FAN CLUTCH TO THE FAN. I HOPE THIS HELPS. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING. P.S. BE SURE TO LOOK AT THE NEW CLUTCH TO FIND OUT WHICH DIRECTION THE THREADS GO. SOME OF THESE ARE LEFTY TIGHTY, SOME ARE LEFTY LOOSEY. GOOD LUCK

Posted on Aug 22, 2009

Testimonial: "Very Helpful "

  • 1206 Answers

SOURCE: how do i remove the cooling fan on my 88 ranger

There are four bolts that hold it on at the water pump using a wrench loosen them, then remove the belts,before removing fan blade.once out you can separate it from clutch with another four bolts. reverse install.

Posted on Jan 17, 2010

alicantecoli
  • 22114 Answers

SOURCE: 2003 ford ranger There is no resistance in the

right old trick ,with assistant ,who has to be pretty and blonde ,get assistant to push and hold pedal down ,then you go underneath and using a bar wedged in somewhere push the actuator arm in so the slave closes,as you push it in open bleed nut,then assistant lets the pedal up and repeat ,push pedal down and holds it down whilst you force the arm back with bleed valve open ,close valve and blonde assistant releases the pedal.easy when you know how

Posted on Jan 17, 2010

csmock132
  • 4669 Answers

SOURCE: changing clutch on a 2003 ford ranger how do I

Well to start, you need to remove the shifter from the transmission. Then remove the driveshaft. Then unplug the plugs from the side of the transmission and disconnect the clutch fluid line. Then remove the crossmember. Unbolt the bellhousing bolts. Then have a friend help you remove the transmission. Then unbolt the clutch.

Posted on Jul 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger forum


throw out bearing might be bad

Jul 01, 2014 | 2004 Ford Ranger

1 Answer

How do you remove the clutch master cylinder on a 2003 ford ranger


ITS A TERRIBLE BIG JOB,WHILE YOU ARE AT IT CHANGE THE RESERVOIR AS WELL. DID YOU REPLACE THE CLUTCH AND SLAVE RECENTLY BECAUSE THEY ARE A RETARD TO BLEED THE SYSTEM AFTER.

May 16, 2014 | 2003 Ford Ranger Regular Cab

1 Answer

How do you remove the clutch master cylinder on a 2003 ford ranger


First drain oil at slave cylinder, then remove pipe from master cylinder . disconnect clutch pedal push rod from cylinder , remove bolts holding cylinder to fire wall remove cylinder. wash off any fluid with water as it will damage paint .

May 16, 2014 | 2003 Ford Ranger Regular Cab

2 Answers

How do i remove the fan and pulley on a 1987 ford ranger 2.9 v-6?


The question is: How remove clutch in order to remove fan mounted on its engine-side face.
  • Generally, the clutch drive half shaft must be uncoupled from coolant pump (impeller drive) half shaft using special wrench kit available as loaner from AutoZone (free with $79 approx deposit).
  • Best done after shroud & radiator remove after coolant drained.
  1. Uncouple coolant pump and fan clutch drive shaft(s) as follows:
    1. span across combo-pulley-sheaves-unit mounting bolt heads with large tool kit wrench, and
    2. span inline clutch coupling nut with small tool kit wrench. Then,
    3. turn small wrench (and coupling nut) CW while resisting with large wrench (CCW) to turn coupling nut until disengaged from coolant pump drive shaft.
  2. Remove fan/clutch assembly.
  3. Note direction of mounted fan hub and fan blades orientation to ensure proper re-assembly.
  4. On rear of clutch assy, remove 4 bolts to disengage and remove fan.
  5. Assemble new fan to clutch (or, preferably, new clutch and new fan) using new bolts and washers provided with fan.
  6. Couple fan-clutch assy to coolant pump drive shaft as per opposite of uncoupling step 1, above. (Turn inline nut CCW to tighten...30 ft-lb.
  7. Check that fan can be hand turned...CW.)
  8. Rest shroud over and onto fan.
  9. Replace radiator; remount shroud; reclamp hoses, and refill and air purge cooling system.
remove-fan-pulley-1987-ford-ranger-2-9-v-2cg35myhodwcq1awmwat24pw-4-0.jpg

Aug 12, 2012 | 1987 Ford Ranger

2 Answers

Ford ranger fan clutch


There may be a tool, or you jam a metal tool between two metal parts.
check these out:


Removing Stubborn Clutch fan Ranger Forums The Ultimate Ford Ranger...

Fan clutch removal


Apr 11, 2017 | 1993 Ford Ranger SuperCab

1 Answer

How to adjust the hydrolic clutch on 2003 ford ranger


There is no way to adjust a hydraulic clutch for your vehicle. If it is not working properly, it could be time to do a clutch remove and replace. Before you get to that point, though, make sure you have no leads that could lead to air getting in the system, and that your master cylinder and slave cylinder are working properly. A very good video that you might find helpful is on Youtube at http://www.youtube.com/watch?v=HgNTDGwcjZc&feature=player_embedded
There are also other videos there that can be quite useful.

Feb 21, 2011 | 2003 Ford Ranger Regular Cab

1 Answer

Changing clutch on a 2003 ford ranger how do I


Well to start, you need to remove the shifter from the transmission. Then remove the driveshaft. Then unplug the plugs from the side of the transmission and disconnect the clutch fluid line. Then remove the crossmember. Unbolt the bellhousing bolts. Then have a friend help you remove the transmission. Then unbolt the clutch.

Jul 09, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

How do i remove the cooling fan on my 88 ranger 2.9? it has the clutch fan


There are four bolts that hold it on at the water pump using a wrench loosen them, then remove the belts,before removing fan blade.once out you can separate it from clutch with another four bolts. reverse install.

Jan 17, 2010 | 1988 Ford Ranger

3 Answers

How to remove fan clutch on 94 Ranger 4.0?


THERE IS A SPECIAL TOOL THAT CAN BE RENTED OR PURCHASED AT YOUR LOCAL AUTO PARTS STORE. IT CONSISTS OF A LARGE OPEN END WRENCH AND A LONG FORK-LIKE TOOL THAT GRABS THE NUTS ON THE FAN SO THAT THE WRENCH CAN LOOSEN THE LARGE NUT THAT HOLDS THE FAN CLUTCH TO THE FAN. I HOPE THIS HELPS. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING. P.S. BE SURE TO LOOK AT THE NEW CLUTCH TO FIND OUT WHICH DIRECTION THE THREADS GO. SOME OF THESE ARE LEFTY TIGHTY, SOME ARE LEFTY LOOSEY. GOOD LUCK

Aug 22, 2009 | 1994 Ford Ranger Supercab

1 Answer

The 8mm flange bolt will not loosen on the Belt Tensioner for my 2000 Ford Ranger - how do I remove the fan so I can get to the bolt more easily?


On 2000 ford ranger 3.0 motor. you have to have a special tool to remove the fan clutch from the front of the water pump..The threads are left hand. I used a strap wrench to hold the pulley then used a cheater bar on the fan shaft.

Take the shroud
d off and take screws out if that is all you need.
I am changing water pump now, having a difficult tme with ps and air c. brackets
Hope this helps

Johnson

Apr 27, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2003 Ford Ranger Regular Cab Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...