Question about Ford Laser

Open Question

1992 Ford Laser TX3 Turbo

Hey mate i was just after the inlet and exhaust gap specs for a 1992 TX3 Turbo KH cheers

Posted by on

2 Suggested Answers

Service Dude
  • 201 Answers

SOURCE: is there a alternator the same as a ford laser tx3 turbo

Yes, just make sure that it looks the same, the ford and mazda most of the spares is the smame

Posted on May 13, 2009

motor1258
  • 6674 Answers

SOURCE: my tx3 laser is backfiring, seems like fuel

Had fuel filter replaced & fuel pressure checked ? Good place to start.

Posted on Oct 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I download a workshop service manual that works for a ford laser 89 ke tx3 turbo


the best place to get a proper manual for a vehicle of that age will from HAYNES

Aug 17, 2016 | Ford Cars & Trucks

1 Answer

Ford laser tx3 non turbo cuts out while driving and restart it and it goes for a while and does it again .Turns all the electrical off ,ignition lights etc


The 1st thing you need to do here is read the fault codes stored in the engine control module. Once you have them you can do the diagnostics for those codes.

Jul 15, 2016 | Ford Cars & Trucks

2 Answers

How do you change a timing belt in a ford laser kh 1992 model car?


so fortunately for you the ford laser and the mazda 323 are one in the same. i would refer to this video to see if you can get a full walkthrough of how the process works. below are two links the first is the video the second is a google search with multiple links may be helpful to you as well.
Water Pump Timing Belt Replacement Mazda 323 Google

Nov 04, 2015 | Ford Laser Cars & Trucks

1 Answer

Where can I get a wiring diagram for a 1992 Ford laser KH 1.6lt


It seems the Ford Laser is the same vehicle as the Mazda 323. You can get a manual online here for $15:

http://seo.chiltonsonline.com/Pub/DIY/Product.aspx?ca=Repair&b=17598

May 27, 2012 | Ford Laser Cars & Trucks

1 Answer

My tx3 laser is backfiring, seems like fuel


Had fuel filter replaced & fuel pressure checked ? Good place to start.

Oct 01, 2009 | 1992 Plymouth Laser

2 Answers

Need Valve clearance for '93 kh ford laser


0.10 - 0.15mm inlet
0.18 - 0.23mm exhaust
but you must be carefull because the top of the valve seat becomes concave from wear, a feeler guage will not give the most accurate reading, hope i have been of some hel

May 14, 2009 | 2006 Ford Laser

1 Answer

Is there a alternator the same as a ford laser tx3 turbo


Yes, just make sure that it looks the same, the ford and mazda most of the spares is the smame

May 13, 2009 | 1989 Mazda 323

1 Answer

Radio code


I had the same prob. you will have to take it back to dealer to get a new code. Can be expensive. Shop around for a fiesta radio / 6 CD stacker unit already with a code. Mines out of a '98 fiesta into my '85 Bronco ! Stacker unit fits under passengers seat, cable back to dash via under carpet. Mine was cheaper to buy (from a wreckers) and install my self than the dealers costs to get the new code for an old unit. on-line wiring diagrams avalible.

Cheers !

ozzy

Feb 22, 2009 | Ford Laser Cars & Trucks

1 Answer

Silvia s14


i dont like to just jump at a expensive thing like that. you should pull the intake side off the turbo and check your impeller endplay and up and down movement first. ill se what i can find for specs. but if it is realy loose then we know what ya have to do

Aug 25, 2008 | 1996 Nissan 200SX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...