Question about 2006 Audi A4

Open Question

Audi tcm remove and replacement of transmission control module

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pippall
  • 1486 Answers

SOURCE: 1995 Audi A4 transmission control

If the tranmission codes are the same. yes you can.

Posted on Aug 09, 2009

sandman357
  • 236 Answers

SOURCE: Where to get a 68pin Automatic Transmission

you're looking at over 2k in expenses but ebay would be your best bet

Posted on Feb 23, 2010

agent91
  • 2100 Answers

SOURCE: Where is the Audi A4, 2006 Multitronic (CVT)

The computer usually sits on the wall next to the driver's legs, but yours could be under the seats, or under the dash, that one I don't know, but it should be kept dry, not under the hood. The valve body is in the transmission. It is accessible from underneath, just under the filter, or on top I should say, holds all your shift solenoids etc.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the TCM in my 2005 Chevy colbolt, light come on but car won't start, turn key and anti theft icon comes on but doesn't stay on


TCM ? transmission control module ? Did you have it programmed ? Reprogram the TCM. Refer to Control Module References for programming and setup information.
Transmission Control Module Programming and Setup
The transmission control module (TCM) must be programmed with the proper software/calibrations. Ensure that the following conditions exist in order to prepare for TCM programming:
• The battery is fully charged.
• The ignition switch is in the RUN position.
• The Techline equipment cable connection at the data link connector (DLC) is secure.
Program the TCM using the latest software matching the vehicle. Refer to up-to-date Techline equipment user instructions.
If the TCM fails to program, proceed as follows:
3.1. Ensure that the TCM connection is OK.
3.2. Inspect the Techline equipment for the latest software version.
3.3. Attempt to program the TCM. If the TCM still cannot be programmed properly, replace the TCM.

Feb 08, 2017 | 2005 Chevrolet Cobalt

1 Answer

Code P0706 transmission control module repair cost


You just don't throw a part on, If the problem is the transmission range selector switch (not the control module) the cost to repair will be around $250.00
P0706 AUDI - Transmission Range Sensor Circuit Range Performance
Possible causes- Open or short park/neutral position switch circuit
- Poor park/neutral position switch circuit connection
- Misadjusted park/neutral position switch
- Park/neutral position switch may be faulty
When is the code detected?The transmission range switch detects the selector lever position and sends a signal to the TCM.

Sep 18, 2012 | 2006 Audi A4

1 Answer

Put trans in works great but has a code po 0700


P0700 is a generic fault code indicating a transmission problem. It's possible it's a left over code from the bad transmission you replaced. You may need to have the code cleared at a transmission shop that uses a different code reader to clear the code. Unfortunately, unlike the standard OBDII code reader, the transmission codes don't always reset themselves after a repair is made.

Oct 13, 2011 | 2000 Jeep Cherokee

1 Answer

Where is the TCM located


TCM (transmission control module).The TCM its located under the passenger side carpet. -------- Thanks.Helpmech.

Nov 16, 2010 | 2004 Audi A4

1 Answer

What causes the transmission to flash on the screen in an audi a4 2003?


a problem with the tranmission is indicated by this, the TCM module that controls the transmission must be tested to find out what fault has occured

Jul 02, 2010 | 2002 Audi A4

3 Answers

What is a tcm


Hi

Thanks for using FixYa. The TCM means Transmission Control Module which is part of the PCM or Power Train Control Module and is located in front of the left front tire. You can access it by removing the fender liner.

Please do rate the solution and revert for further assistance.


Thanks
Rylee

Sep 18, 2009 | 2000 Dodge Caravan

1 Answer

Audi A8 transmission trouble


Hi, first i would check the fluid level if it is not a sealed trans. if the fluid level is ok, it may be that the TCM(transmission Control module is malfunctioning. this module controls the actual shift points. the TCM sends the shift signal to the shift solenoids that are located inside the transmission pan. these shift solenoids preform the engagements of the gears on command, which is initiated by this module i speak of. this module may be damaged,in return, causing this confusion in the shifting patterns you are experiencing.

May 16, 2009 | 2004 Audi TT

Not finding what you are looking for?
2006 Audi A4 Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14200 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...