Question about 2004 Ford Freestar

1 Answer

How to remove the rear light on my Freestar license plate

How to remove the rear light on my Freestar mini van license plate; I thank you in advance!

Posted by on

  • Anonymous Mar 30, 2014

    open rear hatch from inside

  • Anonymous Mar 30, 2014

    how to remove headlight

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

In most cases you have to open the rear tailgate remove the panel and then you have access to everything in the door

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear bumper on a 1998 Chevy Express van 1500?


Support the bumper with a jack, disconnect any electrical wires to license plate light, then loosen and remove the bolts that hold the bumper to the frame. Slowly back the jack up and lower it so the bumper can now rest on the floor.

Apr 26, 2014 | 1998 Chevrolet K1500

1 Answer

No ac no heat no power to the to or maybe from the dash control panel


There are 6 bolts that hold the rear trunk panel on the trunk itself: 4 behind the license plate on the outside of the trunk and two inside the trunk panel trim.
1. Remove the license place from the DeVille rear trunk panel.
2. Remove the 4 bolts located below the license plate.
3. Remove the trunk panel (felt) trim inside the trunk.
4. There is a small bolt on each side of inside trunk panel (4mm I believe). Remove them. Each will have a rubber washer on them so you'll know you are removing the correct bolt.
5. From the outside of the trunk, lift out the rear trunk panel. The license plate light (and reverse lights) are removed by turning the light assemblies counter clockwise.

Aug 27, 2013 | 1997 Cadillac DeVille

1 Answer

Replace license plate light


what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

How do I change the light bulb above the rear license plate?


YOU HAVE TO OPEN THE TRUNK LID REMOVE THE BLACK PLASTIC COVER FOR THE TRUNK LID LATCH.REMOVE THE LICENSE PLATE LIGHT HOUSING FROM THE TRUNK LID.REMOVE THE BULB SOCKET FROM THE LICENSE PLATE LIGHT HOUSING.TO REMOVE BULB FROM THE SOCKET SIMPLY PULL IT STRAIGHT OUT OF THE SOCKET.

May 15, 2010 | 2008 Chevrolet Malibu

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

1 Answer

How to remove lens on rear license plate light


you dont the bulbs twist out from the back side carefull or damage may occur to them from the outside

Apr 28, 2009 | 1998 Chevrolet C1500

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

1 Answer

Burned out license plate bulb


open trunk,

remove felt liner from rear of trunk, (liner directly behind rear lights in side trunk) should be 4 plastic Phillips head screws. Loosing screws, then slowly peel liner away. You will see 3 nuts on each side, removing these nuts will loosing the rear light lenses, so you can pull the lense away from the body from the out side to gain access to the license plate bulbs. Re-install in reverse order. While in there I would recommend replacing your brake light and reverse light bulb. Hey your already in there might as well do a little preventive maintance.

Dec 12, 2008 | 1995 Lexus ES 300

Not finding what you are looking for?
2004 Ford Freestar Logo

885 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...