Question about 1992 Nissan Pickup

1 Answer

1984 Pickup Had to get towed today. Truck would not go into any gear after I stopped It seemed to not disengage and truck would shut down when braked to a Stop. Clutch pedal seemed to have no resistance when depressed. Truck has 95K Miles on it. this is the one with 8 Spark Plugs. It has 4 Wheel Drive also. Any suggestions would be helpful. Thanks. Sam welch 1992 nissan pick up.  would not go into gear when stopped at a traffic light. successful engagement only when stepping down hard on the clutch- almost further than the pedal was designed to go down.  once engaged, the truck is in gear once the pedal is moved off the floorboard by about 1/4 inch, then we launch! Master cylinder is 1/4 above minimum line about 3 months ago I noticed an "oil puddle" under the rear of the truck, forward of the rear LH tire.  not much, and I could not imagine where it came from.  checked the engine oil and it was fine.  starting to realize the probably the "oil stain" which stopped shortly after I saw it, and has not repeated may be related to the clutch problem, but not sure where.  Any ideas or suggestions would be helpful and appreciated.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 52 Answers

Your slave cylinder for the clutch is leaking. It's on the bottom of the transmission towards the engine (follow the fluid trail!). Though it's not too difficult to replace, it IS messy. And be careful with what you touch when you have that fluid everywhere, it eats paint. Usually a new slave will come with detailed instructions on how to properly install and bleed it.
Good luck!

Posted on Jan 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1984 nissan 720 pickup truck that i noticed idles high when stopped, then the idle goes low then high and back and forth. What is causing it?


Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Sep 06, 2012 | 1984 Nissan Pickup

1 Answer

Ok please help I was pumping gas today when I was all done I get in my 1500 dodge ram pickup i start the truck (no problem) then I tried to shift my gear to drive the shift indicator was stuck!! WTF damn...


This truck has a park lock, this locks out the shifter unless the brake light is pressed, the electric solenoid that disengages the lock pin is powered by the brake light circuit, so the 1st thing you do is make sure the brake light work, if they do you have much more serious issue like a sticking release cable from the park lock solenoid.

Feb 12, 2012 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

The starter for my ford 460 stays running after gear is disengaged only have power to solenoid when key is in start position when the truck is shut off one can hear the starter whining down after shutting...


There is a spring in the starter that should cause it to disengage after the electricity is removed. Double check that the electricity is removed form the starter side of the solenoid, cause that is the easiest thing to check first. Then take the starter off and have it checked for free at your local auto store. If it seems OK to them it may be the starter is not the right one for the bell housing. If it sticks in to far, the starter gear may be stuck partly in the flywheel.

Feb 13, 2010 | 1986 Ford F 250

4 Answers

Tow/haul does not work on 2000 chevy truck. whereis fuse?


I had a problem with my tow/haul button not working. I came to find out that the gear shift had cut the wire running to the button in two. You may want to check that.

May 05, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Truck been stitting about 5yrs bought new battery and starter but engine still wont turn whats my next step?


tow it! if the rear wheels skid, pull the plugs (1 per cylinder) and put some oil in each cylinder. Tow it and it should certainly turn over a few times. Then put back the plugs and jump start it

Jul 13, 2008 | 1984 Nissan Pickup

Not finding what you are looking for?
1992 Nissan Pickup Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...