Question about Mercury Cars & Trucks

Open Question

Hood release assembly on 1999 mercury mountaineer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sparky1500
  • 1066 Answers

SOURCE: hood release latch is broken

find the cable that is supposed to attach to the latch, and grab it with a pair of pliers or the like and pull.

Posted on Dec 29, 2008

chuck943
  • 783 Answers

SOURCE: cant get spare tire off

The metal sleeve on the end of the cable,you turn it sideways and push it thru the hole in the wheel. If it is stuck to the wheel just pick up on the wheel then tap the sleeve with a hammer.

Posted on Feb 07, 2009

dkeven
  • 62 Answers

SOURCE: need to replace my dpfe sensor on my 1999 mercury mountaineer. Where is it, i would like to change it myself

the sensor is on the rear of your engine next to the firewall on the 5.0 looking at the egr valve just to the right of it, has two small bolts holding it on and holding the stamped steel bracket for its up against

Posted on Jun 04, 2009

  • 90 Answers

SOURCE: HOOD RELEASE CABLE CAME UNDONE AT THE LATCH ASSEMBLY. HOW DO I OPEN IT WITH OUT THE CABLE WORKING?

remove front grille then you have to fiddle about with the catch it is quite tedious but the only way or take to a dealrship

Posted on Jul 03, 2009

tragedy lok
  • 266 Answers

SOURCE: How do I replace the cv axle assembly for a 2002

ITS QUITE A BIT OF WORK YOPU GOTTA REMOVE THE A ARM(LOOSEN)KNOCK OUT THE BALL JOINT HOLDING IT IN PLACE,UPPER AND LOWER,THE HUB BEARING NEEDS TO BE REMOVED AND THAT PRETTY MUCH WHAT HOLD THE AXLE IN PLACE

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I release the emergency brake on a 2003 mercury mountaineer?


Brake release handle should be near the pedal on drivers side kick panel near hood release

May 22, 2017 | Mercury Cars & Trucks

1 Answer

How do i get the power windows up 2005 mercury mountaineer


May have either a bad switch assembly or a bad window motor,
The system will need to be diagnosed.

Feb 22, 2015 | 2005 Mercury Mountaineer

1 Answer

2001 mountaineer hood latch stuck


Your hood release cable probably broke, you'll have to replace it.

Apr 04, 2014 | 2001 Mercury Mountaineer

1 Answer

Location of dtc codeS mercury mountaineer


it is an obdII code reader. the plug that the code scanner ,reader, is under the dash next to the hood release latch its a black plug just to the left

Aug 06, 2012 | 1997 Mercury Mountaineer

1 Answer

Hood release does not work on my 97 mercury mountaineer. How can I get this open without damaging my vehicle?


if you can get to the bolts that hold the lock in place from the front and bottom you can open the hood and replace the bad cable then remount the locking bracket

Feb 11, 2010 | 1997 Mercury Mountaineer

1 Answer

My hood wont close on a 98 mercury mountaineer


if it doesn't lock then i would look at the latch assembly and spray it with wd-40 they get stuck because of rust and corrosion. also take a look at the handle inside the vehicle they also get stuck in the pulled out position and causing the hood to not lock. give it a push to insure it is in the full depressed position. good luck

Sep 22, 2009 | 1998 Mercury Mountaineer

2 Answers

1998 Mercury Mountaineer Plastic Fan


yes this sounds correct but if you want to get a diagram and step by step instructions try "autozone.com"

Mar 08, 2009 | 1998 Mercury Mountaineer

1 Answer

I can't remove my spare tire on my 1999 mercury mountaineer... it is lowered but im not sure how to release the tire.


you half to pick up the tire on one side reach under and turn the hanger in a straight up and down position and shove it up through rim hole

Jan 08, 2009 | 1999 Mercury Mountaineer

1 Answer

Parking Brake Assembly for a 2004 Mercury Mountaineer


go to an advance or auto zone parts store if they are more they will price match

Jan 04, 2009 | 2003 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...