Question about 1997 GMC Sierra

Open Question

How do i replace cab bushings on 1994 gmc k1500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: I am looking for the proper procedure to shift

On my 1997 GMC the manual says, slow to 1 to 3 mph keep wheels straight. Put transmission into neutral and then move floor lever/shifter forward from 2H into 4LO. Do the 2H to N to 4L in one single motion so that it slips in easier,if you linger in neutral it may not mesh gears correctly. You will hear a slight sound when it slips in. Personally I just reversed the procedure to get it back to 2H.

Posted on Jan 24, 2010

Ad
glentrs
  • 2 Answers

SOURCE: 1994 gmc seirra k1500 4.3 engine 4x4 hesitation

check vacuum lines, near air canisters and air filters etc, usually rubber hoses, may be cracked ,split, dry rot enough to let air in. may as well start there.

Posted on May 02, 2010

Transdoc
  • 829 Answers

SOURCE: im installing a 1996 tranny

Will not work, 95 and up are pwm Lock up units.93 and 94 were on/off lock up units.Pump,valve body and solenoid resistance and different. You will have a no lock-up condition and will burn up transmission.

Posted on Feb 07, 2011

  • 217 Answers

SOURCE: how do you replace the rear main seal on a 1994

you will have to remove the transmission to replace the seal.

Posted on Feb 23, 2011

little_shaws
  • 493 Answers

SOURCE: need to rpl ignition lock 98 GMC K1500 PU

Most ignitions you will need to remove the plastic shroud around the steering colum. Have a good look at the complete barel & mount & you should find a small hole. When the key is in a certain position (usualy accessories) there is a little pin in that hole. You push the pin in with small allenkey, jewler screwdriver etc... & the barel will just slide out.

Posted on Jul 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust fuel injectors on 1994 GMC Sierra 5.7L 350?


They don't adjust. They go in the tbi and seat to the bottom if they are leaking you need to change the o rings on them.

Jun 27, 2014 | 1993 GMC Sierra K1500

1 Answer

Fuse panel diagram


Top photo is inside cab and lower photo is under hood .....0996b43f80219b3c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Fuse application and amperage ratings-1994-98 models. Refer to the wiring diagrams for 1988-93 models


0996b43f80219b3b.jpg enlarge_icon.gifenlarge_tooltip.gif

Jan 18, 2014 | 1993 GMC Sierra K1500

1 Answer

Need to rpl ignition lock 98 GMC K1500 PU


Most ignitions you will need to remove the plastic shroud around the steering colum. Have a good look at the complete barel & mount & you should find a small hole. When the key is in a certain position (usualy accessories) there is a little pin in that hole. You push the pin in with small allenkey, jewler screwdriver etc... & the barel will just slide out.

Jul 01, 2012 | GMC Sierra 1500 Cars & Trucks

1 Answer

My truck shakes really bad when i get up to 50. i have replace the tires and had it aligned.


Have u checked the bearings? Shocks? Could also be the control arm bushings, sway bar bushings bad or broken link arms.

Mar 28, 2011 | 1993 GMC Sierra K1500

1 Answer

How do you replace the rear main seal on a 1994 gmc suburban k1500 4x4


you will have to remove the transmission to replace the seal.

Feb 23, 2011 | 1994 GMC Suburban

1 Answer

What is the best engine to replace my 91 350 TBI engine in my 91 gmc single cab stepside. I want more power but dont want to break the bank


454w/smaller carbs, you will go through everything. you could choose 396 old school for gas mileage, great engine.

May 18, 2010 | 1991 GMC K1500

1 Answer

I have an 1989 GMC Sierra K1500(4x4)5-speed. grinds when going...


It may be the transmission input shaft bushing or bearing, located in the rear of the engine crankshaft, in front of the clutch assembly. If the bushing or bearing is dry (needs to be greased), the input shaft will still try to turn with the engine rpm, even though the clutch pedal is depressed. Also, the clutch disc may not be fully releasing, which could possibly be corrected by adjusting the clutch pedal linkage. good luck

Jul 26, 2017 | GMC Sierra 1500 Cars & Trucks

1 Answer

I have a 1998 GMC k1500 and it makes a ticking noise eveytime u step on the gas?


WORN PISTON RINGS MAKE A TICKING NOISE.VALVE LIFTERS MAKE TICKING NOISE.WORN DISTRIBUTOR SHAFT BUSHINGS MAKE A TICKING LIKE NOISE.

Oct 29, 2009 | 1998 Chevrolet K1500

2 Answers

A/c and heater only blow air out of defrost


sounds like there is a vacuum leak, possibly under the hood.. Vaccumm is needed to change the mode doors.

Mar 30, 2009 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

No problem,just confused.


You will usually find that it is the model number.
Or maximum total weight of vehicle.
Check your drivers manual

I had a dodge ram 2500, which only had a 1/2 ton capacity.
good luck

Jan 25, 2009 | 1993 GMC Sierra K1500

Not finding what you are looking for?
1997 GMC Sierra Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...