2007 Honda CR-V Logo

Related Topics:

A
Anonymous Posted on Nov 04, 2012

Towbar wiring for honda crv

Where can i connect caravan electrics

2 Related Answers

Anonymous

  • 33 Answers
  • Posted on Jul 21, 2009

SOURCE: wiring diagram for 2055 towbar for honda crv

The best place to connect the wiring is behind the left trim in the boot, there is a grey socket which has all that you need except the fog which can be located in the wiring loom to the left light unit.

Ad

Anonymous

  • 1851 Answers
  • Posted on Mar 18, 2010

SOURCE: where do i feed the wires through to wire up the

If you have a wired tow hitch on your car you will need to mate this to the wiring harness on the tow bar. If the two wired units do not match then you will either need an adapter or will need to rewire the tow dolly or the car. If the car doesn't have a tow light unit installed you will need to install one that will mate to the tow bar light unit.

I hope this helps - please rate me

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where is the knock sensor on 2003 honda crv

The knock sensor on a 2003 Honda CRV is located on the engine block. Specifically, it is located under the intake manifold, which means it can be difficult to access. Here are the steps to locate and replace the knock sensor on a 2003 Honda CRV:
  1. Disconnect the negative battery cable to prevent electrical shock.
  2. Remove the intake manifold. This involves removing several bolts and electrical connections.
  3. Locate the knock sensor, which is located near the rear of the engine block, under the intake manifold.
  4. Disconnect the electrical connector from the sensor.
  5. Remove the sensor from the engine block. This may require a special tool, depending on the specific design of the sensor.
  6. Install the new knock sensor, making sure it is properly aligned and tightened to the correct torque specification.
  7. Reconnect the electrical connector to the sensor.
  8. Reinstall the intake manifold, making sure all bolts and electrical connections are properly secured.
  9. Reconnect the negative battery cable.
Note that if you are not experienced with working on engines or are unsure of how to proceed, it may be best to seek the assistance of a qualified mechanic to replace the knock sensor on your 2003 Honda CRV.
0helpful
1answer

2013 CRV intermittent groaning/ moaning sound from rear near side corner when towing caravan. No effect on drive or handling just a moan

take it to a panel repair shop and have the body checked around the tow bar area and rear end suspension points for loose spot welds, cracked body floor panels, loose towbar bolts etc
to get any noise there has to be something moving, stretching or cracking so a very close inspection should be made
1helpful
1answer

Can you show me where the fuses are for the electric windows are for a 1996 honda crv

This looks to be the entire wiring diagram of a honda CRV. Couldn't find one for 96 but hopefully this is close enough to get you the answers you wanted. http://www.autowiringmanual.com/wp-content/uploads/2011/09/1997-crv-system-wiring-diagrams.pdf
0helpful
1answer
3helpful
1answer

Honda CRV 2007 Diesel PGM-FI Light comes on whenever a trailer is connected to the towing electric hook up, have a feeling it is something to do with a poor ground on the trailer as it has happend numerous...

I also have made similar experience with my CRV-2007. I made the warning light disappear by taking off the battery power for some hours, starting up and driving a short tour with the car.
0helpful
1answer

Where do i feed the wires through to wire up the towbar on a 1997 honda crv?

If you have a wired tow hitch on your car you will need to mate this to the wiring harness on the tow bar. If the two wired units do not match then you will either need an adapter or will need to rewire the tow dolly or the car. If the car doesn't have a tow light unit installed you will need to install one that will mate to the tow bar light unit.

I hope this helps - please rate me
0helpful
1answer

E320 CDI 2001 W210 TOW BAR WIRING

Perhaps this link will be of help to you. http://www.watling-towbars.co.uk/towbars.html
2helpful
1answer

Towbar wiring for bmw x3

I dont know this particular model but if you go to a caravan sales pitch ,they usually have the wiring diagrams at the back of their caravan brochures. You could always tell them that you,re interested in getting a caravan but dont know if your car can be wired for one.Also try towbar sellers, they always give out the diagrams. Hope this helps.
May 20, 2009 • 2009 BMW X3
4helpful
1answer

Wiring diagram for 2055 towbar for honda crv

The best place to connect the wiring is behind the left trim in the boot, there is a grey socket which has all that you need except the fog which can be located in the wiring loom to the left light unit.
1helpful
2answers

Volvo V70 2001.. Plugs For Towbar Electric's??

You can get an adapter that fits in to the 13 pin socket that give you a 12N socket, easily available on E-bay

http://cgi.ebay.co.uk/13-to-7-Pin-Adaptor-for-Euro-Style-Towbar-Electrics_W0QQitemZ110303426204QQihZ001QQcategoryZ36631QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

I have one for my car and it does the trick
Not finding what you are looking for?

209 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...