Question about Cars & Trucks

Open Question

How to change clutch inhibit switch 2000 gmc sonoma

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: how do you add clutch fluid?

hi it is next to the brake master cylnder on the firewall. it will have its own resevoir for the fluid,the small round one will only hold about a cup of fluid

Posted on Feb 02, 2009

Ad
  • 71 Answers

SOURCE: where is the fuel shutoff switch on a 1996 gmc sonoma?

no fuel shut off switch on pickups that i know of possibly bad fuel pump find your red bypass wire at relay to test pump

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: what is the firing order on a 2000 4.3 gmc sonoma?

i dont know how they got it....i was just told that they got it......MEN!!!!

Posted on Jun 17, 2009

SOURCE: 1995 gmc sonoma ignition key worn out

You have to remove the stering colum covers and in the ingnition key drum on the side there is a little hole, press the inside pin and pull the key ccylinder out, you can buy on autozone or pep boys.

Posted on Jul 18, 2009

dnewcombe1
  • 1564 Answers

SOURCE: Replacing heater core in 2000 GMC sonoma. Dash is

If the dash is removed you've saved about 9 10ths of the job endurance. Look around, what you believe to be, the perimeter of the heater box. I cannot, and no one else can, tell you exactly where the bolts and nuts that mount the heater box are. Therefore you must viually sixe the box and check outide in the engine compartment and inside under the dash for the mounting bolts.You'll want to start by removing the heater hoses. Then starting at the passenger side engine compartment look for a group of 10mm or 7/16ths nuts retaining the housing and remove them. Do the same inside. The housing is usually held together with screws or clips, it changes year to year. Keep a log or pix of the wires and cables and hoses(vacuum) that are connected to the housing for reassembly. You'll need to "roll" the box out from under the dash depending on how much of the dash has been removed. The core is easy to spot for is has two hoses sticking out, and, is encircled with clips or screws . Also make sure you remove the bracket around the two entry hoses if it has one. Thank you, Dana

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 gmc sonoma which I recently had clutch replaced however it still won't go into gear. Any suggestions as to what else it cold be?


did you have it pro replaced? If so, you should take it back to them. How long is your warranty? If you personally replaced, you need to check the service manual. Here is the owner manual

1999 GMC Sonoma TSBs CarComplaints com

and you may find this info about clutch issues here
How to Adjust the Clutch on 1997 GMC Sonoma eHow

Jan 10, 2015 | 1999 GMC Sonoma

1 Answer

2000 gmc sonoma wont start all the time has new starter and key switch


If the engine will not crank, you'll need to know if you have power at the starter posts. It could be the neutral switch or the starter relay.

Mar 08, 2014 | GMC Sonoma Cars & Trucks

1 Answer

`1998 GMC SONOMA WONT START WITH KEY ON CLUTCHPUSH IN STARTER OKBUT MOTOR TURN OVER


clutch safety switch bad. may be bad wire/fuse. shld be located on the clutch pedal normally kind of square to oblong box type switch abt inch and half long.you can unplug it, and place a jumper wire in the plug terminals and if it starts then you know its the switch (note: it works the same as a nuetral safety switch on an automatic)

Aug 27, 2012 | 1998 GMC Sonoma

1 Answer

How do I replace the neutral safety switch on my 2000 GMC Sonoma 5 speed?


Does not have a neutral safety switch , it has a clutch inhibit switch.It is located at the top of clutch pedal and is threaded into a bracket or is on the rod that goes from clutch peadl to master cylinder.

Feb 27, 2011 | GMC Sonoma Cars & Trucks

1 Answer

Where is low pressure switch on 2000 gmc sonoma


Find the ac compressor,and follow the large line until you come to it.

Jun 09, 2010 | 2000 GMC Sonoma Extended Cab

2 Answers

Alkadljadjladaljd


Just over half is usually when the fans switch on to cool so this should be correct, when cool check water (low oil will not affect tick over temp) , then moniter it if no water loss then dont worry.

Oct 18, 2009 | 2000 GMC Sonoma Extended Cab

4 Answers

1870 code


You're dealing with one of the problems listed below:

A cracked or leaking TCC (torque converter clutch control) solenoid.

A cut, damaged or missing turbine shaft O-ring seal.

A converter clutch valve which does not have full travel of 1/2" or is stuck in the off position.

A slipping clutch or band.

Jul 24, 2009 | 2000 GMC Sonoma Extended Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...