Question about 2001 Nissan Maxima

2 Answers

Location of a o2 sensor 2001 nissan maxima

2001 nissan maxima, which o2 sensor is bank 1 sensor 2 ?

Posted by on

  • 14 more comments 
  • Anonymous Feb 18, 2009

    Service Engine soon light is on. When checked, I got a P0420 code which means the 02 sensor has malfunctioned. I dont know if it is Bank 1 sensor 1 or bank 1 sensor 2?

  • nie puk Aug 23, 2013

    replace new one light but light on

  • Anonymous Mar 14, 2014

    lcation of bank 1 sensor 1 in a 2003 nissan maxima

  • Anonymous Mar 15, 2014

    Sopped in Traffic, my lights went deem and my 2001 Nissan Maxima shuts off. Jump started it but the lights went deem and it shuts off again and I had to tow it away.

  • Anonymous Mar 16, 2014

    Location of the number 3 cylinder of a 2002 Nissan Maxima

  • Anonymous Mar 19, 2014

    where is the cam sensor a located on a 2006 nissan maxima?

  • Anonymous Mar 19, 2014

    where is the bank a cam shaft sensor is located on a 2006 nissan maxima 3.5 engine?

  • Anonymous Mar 19, 2014

    3.8

  • Anonymous Mar 19, 2014

    which is in need of passing the smog check but doesn't due to O2 sensor 1 Bank 1, which one is it? and or what is its location in the car?

  • Anonymous Mar 22, 2014

    Where the PVC valve located on a 2006 Nissan Maxima

  • Anonymous Mar 22, 2014

    Where the PVC valve located on a 2006 Nissan Maxima

  • Anonymous Mar 23, 2014

    replace new alternator

  • Anonymous Mar 23, 2014

    What is the O2 sensor of bank 2 of 2005 XL7 susuki

  • Anonymous Mar 23, 2014

    location of abs control module

  • Anonymous Mar 27, 2014

    right side or left side?

  • Anonymous Mar 29, 2014

    how to remove the TPS in a 2001 Nissan Maxima

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Posted on Jan 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need to rev the rpms to srat it when cold but then the car runs fine when its been running for a while but after it sits for about 4 houres or more i need rev the rpms again to get it going

Posted on Nov 22, 2013

  • Jay Leduc
    Jay Leduc Nov 22, 2013

    i need to rev the rpms to srat it when cold but then the car runs fine when its been running for a while but after it sits for about 4 houres or more i need rev the rpms again to get it going

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have 01 nissan maxima and it has p132 code and cutoff but will crank back what is the problem


P0132 Nissan - Engine-Codes.com

engine-codes.com/p0132_nissan.html
P0132 Nissan O2 Sensor Circuit High Bank 1 Sensor 1. ... 2002 Nissan Sentra andAltima Factory Service Bulletin OBDII Code P0132 · What does this mean?

P1320 Primary Ignition Signal Fault Testing and ... - YouTube

? 12:27
www.youtube.com/watch?v=kpFzunNeAaY
Aug 15, 2014 - Uploaded by CarsNToys This was performed on a 1997 Nissan Maxima. ... Code P1320 is indicated when ignition signal in the primary circuit (of the ... $1000 and could not find the problem out with my 2001 maxima.but now at ..... 2016 Nissan Maxima SL - Ultimate In-Depth Look - Duration: 43:16. by MikesCarInfo 261,066 views.

Sep 16, 2015 | Nissan Cars & Trucks

1 Answer

2001 nissan maxima engine misfire


The Fuel Pump, I assume failed & was another issue

The Fuel filter is changed every 3 years, as preventative
maintenance

The Codes for the most part are O2 Sensors, that are over six
or seven years old & over 100,000 miles & should be replaced
as preventative maint or if they fail ,sooner

You don't throw out any what if senerios, or replace any parts
in an effort to resolve anything

You component test & replace only failed parts, related to the codes
& system that has a fault & drivability symptom

You should know if the spark plugs are over 3 years old

Clean the MAF Sensor & check for vacuum leaks on the entire car

Aug 01, 2012 | 2001 Nissan Maxima

1 Answer

Location of o2 sensor bank 1 sensor 2


Bank 1 sensor 2 is the O2 sensor behind the catalytic converter.

Apr 08, 2011 | 1999 Nissan Sentra

2 Answers

Hi, I have, 2001 Nissan Maxima. Get check engine lite. Car now has 60k miles. Local mechanic had already replaced two O2 sensors 9 months ago. I don't know what the codes were at that time. Check Engine...


renew the O2 sensors to start with and just hope that its a bad sensor on this bank they can break down prematurely .Luck of the draw their when buying new parts iam afraid your not the only one to buy new parts and have them go early .

Jan 18, 2011 | 2000 Nissan Maxima

1 Answer

Where is o2 sensor designated bank 1 sensor 1 located on 1999 nissan maxima and how do change it also what is the replacement part number


Bank 1 is the side Cyclinder 1 in on, sensor 1 is befor cat converter. I think 7/8 box wrench, as in difficulty that depends on what in in the way.

Jan 02, 2011 | 1999 Nissan Maxima

2 Answers

P0171B


It means that your engine is running lean - not getting enough fuel for the amount of air that the engine is receiving. Because your maxima is equipped with a V-6 engine, whatever the problem, it is affecting only bank #1. Bank #1 is always the side of the engine where cylinder #1 is located, or in your case, the left side of the engine as it is viewed while facing the crankshaft end of the engine.
(on a 4 cylinder engine, there is only one bank and it is always referred to as Bank #1)
There are several things that can cause a lean condition including vacuum leaks, a malfunctioning Evaporative Emissions system, a misfiring cylinder (due to bad plugs, bad injectors, or an intake or head gasket leak.), a malfunctioning Mass Airflow sensor (MAF) or Manifold Absolute Pressure sensor (MAP) or even a bad Oxygen sensor (O2s) (Nissan sometimes calls an O2s an "Air-Fuel Ratio Sensor") It is even possible for a leaking vacuum brake booster to cause a lean code.
If there are any other malfunction codes present, it may help to pinpiont the cause of the lean code. (Like a P0301 "cylinder#1 misfire detected", in which case, you would address the misfire code first.)
Certain problems, like a leaking brake booster or a bad MAF will usually set lean codes for BOTH banks.
If the P0171 is the ONLY code present, the most likely cause is a bad O2s, but I recommend some diagnostic testing to prove it before spending the mega-bucks that Nissan gets for their O2 sensors.

Oct 10, 2009 | 2000 Nissan Maxima

1 Answer

Im getting a code 51 from the on borad computer on


Do you mean P0051??

If you do, then it's an issue with one of your O2 Sensors.

You may have a short in the heater circuit in the sensor
The O2 sensor heater has failed
The wires connecting the sensor are broken or frayed

Most likely you will need to replace the sensor.
The sensor is Bank 2 Sensor 1
Bank 2 means it is located opposite of where cylinder 1 is (not sure where cylinder 1 is on your car) and Sensor 1 will mean it's the sensor located before the catalytic converter

Sep 25, 2009 | 1994 Nissan Maxima

1 Answer

O2 sensor and EVAP issues


P0446 is Aux Emission Control
P0132 Fuel Air Metering

The Evap Canister is located in the fender well, if I am not mistaken and the B1S2 is the O2 sensor is the second O2 sensor on the left side of the engine if your looking at it from the front of the motor.

Aug 21, 2008 | 1997 Nissan Maxima

Not finding what you are looking for?
2001 Nissan Maxima Logo

4,724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...