Question about 1990 Chevrolet Cavalier

1 Answer

Alternator installation 1990 Cavalier

I cannot put the belt on (with a/c) if I install the alternator first and I cannot align the bolts with the bracket if I put the belt on the alternator first. There is a bracket that is attached to all the pulleys that seems to get in the way and doesnt allow to install the alternator with one bolt to use as a pivot point.

Posted by on

  • scott thomas May 11, 2010

    what size motor do you have 2.0 or 2.8

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Dont know if this will help but loosen the tensioner to put the belt on.

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

1 Answer

Please could you give me a diagram of the valve timing of a double O.H.C.on a toyota Rav4 3SFE engine


no year(94-present) stated. and under kia dont help much.

its at alldtata.com, i read all the steps and not skip one, I WOULD.

wild guess, #1 a 2005 RAV4
2.0L 3sfe. inline 4 cylinder, not V6


here is the one i see on the FSM.

my gates belts all come with a manual. RTM?
if you buy the belt at a dealer they assume you have the FSM.
right?
FSM, install, steps
  1. Install the oil pump pulley. Tighten the nut to 18 ft. lbs. (24 Nm).
  2. Install the crankshaft timing pulley. Align the pulley set key with the key groove of the pulley. Slide on the pulley facing the flange side inward.
  3. Install the No. 2 idler pulley and tighten the mounting bolt to 31 ft. lbs. (42 Nm). Be sure that the pulley moves smoothly.
  4. Install the No. 1 idler pulley with the bolt and the tension spring. Pry the pulley toward the left as far as it will go and tighten the bolt. Make sure that the pulley moves smoothly.
  5. Temporarily install the timing belt. Using the crankshaft pulley bolt, turn the crankshaft and position the key groove of the crankshaft timing pulley upward. If reusing the timing belt, align the points marked during removal.
  6. Install the timing belt on the crankshaft timing pulley, oil pump pulley, No. 1 idler pulley, water pump pulley and the No. 2 idler pulley.
  7. Install the timing belt guide.
  8. Install the lower (No. 1) timing belt cover and new gasket with the 4 bolts.
  9. Align the crankshaft pulley set key with the pulley key groove. Temporarily install the crankshaft pulley and bolt.
  10. Align the camshaft knock pin with the groove of the pulley, and slide the timing pulley onto the camshaft with the plate washer and set bolt.
  11. Tighten the pulley set bolt to 40 ft. lbs. (54 Nm).
  12. Turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  13. Finish installing the timing belt and check the valve timing, as follows:
    1. If reusing the old timing belt, align the matchmarks made previously and install the timing belt onto the camshaft pulley.
    2. Align the marks on the timing belt with the marks on the camshaft pulley.
    3. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    4. Turn the crankshaft pulley 2 complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    5. If the No. 1 idler pulley uses a green tension spring, slowly turn the crankshaft pulley 1 7 / 8 revolutions, and align its groove with the mark at 45 degrees BTDC (for the No. 1 cylinder) of the No. 1 timing belt cover.
    6. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    7. Be sure there is belt tension between the crankshaft and camshaft timing pulleys.
  14. Place the right-hand engine mounting bracket in position but do not install the bolts.
  15. Install the upper (No. 2) timing cover with a new gasket(s).
  16. Remove the engine crankshaft pulley bolt and pulley.
  17. Using SST 09249-63010, or equivalent, install the mounting bolts for the right-hand mounting bracket. Tighten the mounting bolts to 38 ft. lbs. (52 Nm).
  18. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  19. Install the spark plugs.
  20. Install the right-hand mounting insulator, as follows:
    1. Attach the mounting insulator to the body and mounting bracket with the 4 bolts and 2 nuts.
    2. Tighten the 3 bolts to hold the mounting insulator to the body. Tighten the bolts to 47 ft. lbs. (64 Nm).
    3. Tighten the 2 nuts and bolt to hold the mounting insulator to the mounting bracket. Tighten the bolt to 27 ft. lbs. (37 Nm) and the nut to 38 ft. lbs. (52 Nm).
  21. Install and adjust the power steering pump drive belt.
  22. Install the right-hand engine undercover.
  23. Install the right front wheel.
  24. Lower the engine.
  25. If equipped, install the ABS actuator.
  26. Install the alternator and alternator bracket.
  27. Install the wiring harness bracket for the DLC1.
  28. Install the power steering reservoir bracket and reservoir.
  29. Connect the negative battery cable.
  30. Start the engine and check the timing.

step 13.4 is never to be skipped. ask why., most do. and it fails.






a70ecb7d-3231-4383-bdd9-edd2200c74a4.jpg

Jun 07, 2014 | 2002 Kia Sportage

1 Answer

How do you aline the timing marks on the cam and crank on a 97 toyota camry with a 2.2


Hi, the procedure is pasted below. There is a good rundown with pics at the following post:
http://www.toyotanation.com/forum/showthread.php?t=264429
Please let me know if you have questions.


REMOVAL & INSTALLATION
5S-FE Engines
  1. Remove the timing belt covers as previously detailed.
  2. Raise the engine just enough to remove the weight from the engine mount on the right side.
  3. Remove the thru-bolt, two nuts, and right hand mounting insulator.
  4. Remove the retaining bolts and remove the right hand mounting bracket (from the side the alternator was removed from).
  5. Remove the timing belt and timing belt guide. If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear.
  6. Remove the bolt retaining the No. 1 idler pulley and tension spring.
  7. Remove the No. 2 idler pulley.
  8. Remove the crankshaft timing gear , if it can not be removed by hand, use two flat bladed tools to pry it off. Make sure to position shop rags to prevent damages to the components.
  9. Remove the nut retaining the oil pump pulley.

To install:
  1. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
  2. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
  3. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly.


NOTE Remove any oil or water on the idler pulley and keep it clean.
  1. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
  2. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys.


NOTE If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.
  1. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
  2. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  3. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
  4. Align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.
  5. Tighten the set bolt to 27 ft. lbs. (37 Nm).
  6. Turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  7. Install the timing belt and check the valve timing as follows:
    1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
    2. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.

  8. Install the upper (No. 2) timing cover with a new gasket(s).
  9. Align the two clamps for the engine wiring harness with the cover mounting bolts.
  10. Install the spark plugs.
  11. Install the right mounting insulator with bracket. Tighten the bracket bolts to 38 ft. lbs. (52 Nm), insulator nuts to 38 ft. lbs. (52 Nm) and thru-bolt to 52 ft. lbs. (71 Nm).
  12. Install the No. 2 engine mount bracket and tighten to 38 ft. lbs. (52 Nm); install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm).
  13. Lower the engine.
  14. Install the alternator and alternator bracket.
  15. Install the drive belt and adjust the tension.
  16. Install the cruise control actuator with bracket.
  17. Install the fender apron seal and right engine under cover.
  18. Install the right front wheel.

Jul 24, 2011 | 1997 Toyota Celica

1 Answer

Changing alternator



REMOVAL & INSTALLATION 2.2L Engines
CHRYSLER ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.

When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.
To install:
  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.

To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

Jan 02, 2011 | 1994 Plymouth Voyager

1 Answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?


check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif

Oct 29, 2010 | 2000 Honda Accord

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

1 Answer

How do i replace an alt on an 97 Grand Voyager?


When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Jul 08, 2010 | 1997 Plymouth Grand Voyager

1 Answer

Changing alternator


REMOVAL & INSTALLATION
2.2L Engines
CHRYSLER ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.
When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.

To install:

  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.
To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

2.5L Engines
2.5L engines were equipped with either Chrysler or Bosch alternators.

  1. Disconnect the negative battery cable.
  2. Remove the drive belts.
  3. Remove the adjusting bracket-to-engine mounting bolt.
  4. Remove the adjusting locking bolt and nut, then remove the mounting bracket.
  5. Position the alternator to gain access to the wiring.
  6. Disconnect the wiring and label for easy installation.
  7. Remove the pivot bolt, nut, and washers.
  8. Remove the alternator assembly from the engine.
To install:
  1. Position the alternator assembly against the engine.
  2. Loosely install the pivot bolt, washers, and nut.
  3. Attach all wiring connectors to the alternator.
  4. Position the mounting bracket in place, then install engine mounting bolt.
  5. Loosely install the adjusting locking bolt and nut.
  6. Install the drive belts, and adjust to specification.
  7. Tighten all mounting bolts and nuts.
  8. Connect the negative battery cable.

2.6L Engines
2.6L engines were equipped with Mitsubishi alternators.
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the adjusting strap mounting bolt.
  4. Remove the drive belts.
  5. Remove the support mounting bolt and nut.
  6. Remove the alternator assembly.
To install:
  1. Position the alternator assembly against the engine, then install the support bolt.
  2. Install the adjusting strap mounting bolt.
  3. Install the alternator belts and adjust to specification.
  4. Tighten all the support bolts and nuts.
  5. Connect all of the wiring terminals to the alternator.
  6. Connect the negative battery cable.

3.0L Engines
The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
  1. Disconnect the negative battery cable.
  2. Install a 1 / 2 in. breaker bar in the tensioner slot. Rotate counterclockwise to release belt tension and remove poly-V belt.
  3. Remove the alternator mounting bolts (2).
  4. Remove the wiring and remove alternator.
To install:
  1. Position the alternator onto the engine, then install the wiring.
  2. Set the alternator against the mounting bracket and install the mounting bolts.
  3. Rotate the tensioner counterclockwise and install poly-V belt.
  4. Connect the negative battery cable.

3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators.
  1. Disconnect the negative battery cable.
  2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner.
  3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
  4. Remove the alternator tensioner/power steering bracket bolt.
  5. Remove the tensioner stud nut and remove the tensioner.
  6. Remove the alternator mounting bolts.
  7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
  8. Remove the alternator support bracket bolts. Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
  9. Remove the alternator from the engine and disconnect the electrical leads.
To install:
  1. Install the alternator in position on the engine and connect the electrical leads.
  2. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm).
  3. Install the power steering reservoir on the mounting bracket.
  4. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
  5. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
  6. Install the alternator belt, insert a 1 / 2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
  7. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 01, 2010 | 1994 Dodge Caravan

1 Answer

Replacing alternating belt


A good repair manuel to get which has picture step by step, Hanyes auto repair manuel at any aut part store for 20 bucks is a great investment.
.0l Engines The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
1. Disconnect the negative battery cable.
2. Install a 1/2 in, breaker bar in the tensioner slot. Rotate counter-clock- wise to release belt tension and remove poly-V belt.
3. Remove the alternator mounting bolts (2)
4. Remove the wiring and remove alternator.
To Install:
5. Position the alternator onto the engine, then install the wiring.
6. Set the alternator against the mounting bracket and install the mounting bolts.
7. Rotate the tensioner counterclockwise and install poly-V belt.
8. Connect the negative battery cable. 3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators. 1. Disconnect the negative battery cable.
2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner
3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
4. Remove the alternator tensioner/power steering bracket bolt.
5. Remove the tensioner stud nut and remove the tensioner.
6. Remove the alternator mounting bolts.
7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
8. Remove the alternator support bracket bolts, Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
9. Remove the alternator from the engine and disconnect the electrical leads.
To Install:
10. Install the alternator in position on the engine and connect the electrical leads.
11. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm). Install the power steering reservoir on the mounting bracket.
13. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
14. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
15. Install the alternator belt, insert a 1/2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
16. Connect the negative battery cable.

Oct 09, 2009 | 1994 Dodge Caravan

1 Answer

HOW HARD IS IT TO REMOVE AN ALTERNATOR


Yes, very easy...here is the steps to do it:

To Remove:
  1. Disconnect battery negative cable.
  2. Remove air cleaner inlet pipe.
  3. Disconnect alternator electrical connections.
  4. Loosen (but do not remove) pivot bolt and tensioner mounting bolt.
  5. Remove drive belt form alternator pulley.
  6. Remove tensioner mounting bolt and belt tensioner.
  7. Remove pivot bolt, loosen adjusting bracket bolt and rotate bracket up.
  8. Remove alternator.

To Install:

  1. Place alternator on engine.
  2. Install (but do not tighten) pivot bolt.
  3. Rotate bracket down on top of alternator.
  4. Install belt tensioner and install bolt loosely.
  5. Install drive belt on alternator pulley.
  6. Tighten tensioner bolt to 14-19 ft lb (19-26 Nm).
  7. Tighten pivot bolt and bracket bolt to 28-38 ft lb (38-51 Nm).
  8. Connect alternator electrical connections.
  9. Install air cleaner inlet pipe.
  10. Connect battery negative cable.

120f25e.gif

Jul 13, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
1990 Chevrolet Cavalier Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...