Question about Cars & Trucks

1 Answer

How do I get the King pin out - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,848 Answers

Heat and a big pin punch and a large ball pen hammmer.

Posted on Nov 05, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1952 chevy truck king pins install


Remove the road wheels, remove front hub from stub axles, remove the cotter pin nut and drive out the pin, remove the welch plug on the top of the king pin and with a drift drive the pin through the axle, press the old bushes from the stub axle and press in new bushes, ream the bushes till the king pin will just slide in .Then assemble make sure there is no play between the pivot bearing and stub axle use shims if required.

Sep 24, 2014 | Cars & Trucks

1 Answer

How do i replace king pins on 1939 buick?


In general terms, you would remove the front wheels, remove the retainer clip or lock for each pin, and drive the pins out with a brass punch or other tool. Then the bushings can be replaced.
I would suggest getting a repair manual for the car or for that era since each make is different. Sometimes a special puller is needed.

Sep 01, 2014 | Cars & Trucks

1 Answer

I need to replace the front king pin in the r/h side wheel of my El fairmont.. how do I do this ??


I take it that this is a Ford car in which case I doubt very much that it has king pins in the front end. It will have either an upper and lower ball joints in control arms or a lower ball joint on the end of a strut. Ford ball joints are riveted in from factory and the rivets have to drilled out and the new ball joints will have the correct bolts to replace the rivets IN the case of a strut the lower ball joint is replaced as above and the strut will have a replaceable insert in it that you can remove and fit a new insert in place . Ford stopped using king pins when they gave away "I" beam front axles .

Jun 09, 2014 | Cars & Trucks

1 Answer

King pins


sound like worn tie rod ends or worn ball joints.

Jul 28, 2013 | Ford Cars & Trucks

1 Answer

Replace king pins on f 250 two wheel drive


I think you will find they are swivel joints top and bottom,if it is king-pins a press,reamers and a very striaght eye..will be required.Either way the front hub assemblies will need to be stripped down..Good-luck....

Jan 06, 2013 | 2001 Ford F250 Super Duty Super Cab

1 Answer

I have a 1985 f 250 and in the book it shows ball joints but mine seams to have king pins mine is the base f250 with the 6.9 ltr engin


Hello mjohns0542,

Unless you have 4 wheel drive you will have king pins. See image below.

netvan_214.png

I hope this helps.

Regards,

Jerry

Aug 28, 2011 | 1985 Ford F 250

1 Answer

How can I remove the kin pins and replace took truck for wof and failed on king pins on right front but dont know how to remve them


This job requires special tools. It will not be JUST the king pins, but the surfaces that the pins touch, also. This job requires tools to remove, reinstall and fit the pins. I suggest a shop for this job.

Mar 20, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

I have a 1989 ford bronco the front end shakes and pops


Is this bronco twin I beam with king pin and bushings or does it have control arms. BOTH avail that year. IF it is king pin and bushing front end.. that is your problem . JUST replace the king pin and bushings

Feb 21, 2011 | 1989 Ford Bronco

1 Answer

Hear a popping noise when braking. Could this be


This vehicle does not have king pins. There are a lot of front end parts that go bad. Ball joints, stab links, sway bar bushings. Best bet would be to have a proffesional take a listen to it.

May 07, 2010 | 2004 Ford F350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...