Question about Ford Cars & Trucks

Open Question

Diagram 1996 town country rear heater core - Ford Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

mecanica03
  • 881 Answers

SOURCE: How to replace a evaportor core in a 1996 Town

the only way to replace evaporator core is by removing dash pannel, its very hard, i to make this work 2 years ago and i dont have to know about this again, i recomend you go to a good place to do, good look

Posted on Jul 05, 2009

wracefans24
  • 1985 Answers

SOURCE: 1996 town & country van front heater blower

you will need to start by checking fuse,then power to motor,then blower motor resistor

Posted on Jan 29, 2010

  • 181 Answers

SOURCE: remove expansion valve in 1996 town and country

Once you disconnect the lines there are two torx screws that hold it in place. Once removed it should just pull off.

Posted on May 19, 2010

  • 266 Answers

SOURCE: 2003 town & country heater core replacement

TAKE IT TO A SHOP ITS NOT ONE YOU WANT TO DO LABOR TIME IS ABOUT 11 HOURS THAT MEANS ALOT OF THE DASH NEEDS TO COME OUT

Posted on Oct 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed thermostat, radiator, water pump, hose, engine cooling temperature sensor, radiator cap and I'm still overheating. 2004 Chrysler town and country


Check the heater cores. There are usually 2 in a T&C. Also check the pipes running to the rear heater core. I recently had to have mine repaired because they were leaking!

May 22, 2015 | 2004 Chrysler Town and Country

1 Answer

Where is the rear heater core located on a 2002 town and country minivan?


hi,
Generally, in motor vehicles, the cabin air fans get the warm air from the same hot water/coolant circulating through the engine.
Surely, the leaking staff is antifreeze from the air blower heater element like a radiator. check the hoses in case of breaking and their joint in case of loose clamps.

Ngosa

Dec 08, 2013 | 2002 Chrysler Town & Country

1 Answer

I have a coolant leak in a 96 town and country


TRACE LOCATION AND FIX, HOSE OR CLAMP OR RADIATOR OR HEATER CORE IN DASH . IT IS A SMALL CLOSED SYSTEM UNDER PRESSURE

Nov 03, 2013 | 1996 Chrysler Town & Country

1 Answer

My heater hoses have been removed and bypassed. I need a heater hose diagram for my 1998 chrysler town and country van with a 3.8 L. I don't know which hose will plug into which heater core tube


That's easy

Drive around back of a dealer,walk in the open
service bay doors & ask a tech to come out &
tell you.

I walk into dealers all the time, anywhere I want to go,
& never get stopped

If your questioned your just looking for the parts dept & leave

Feb 01, 2013 | Cars & Trucks

1 Answer

No heat 1996 chysler town and country. When I turn on blower water comes from passenger side under dash.


This usually indicates that the heater core( a thing that looks and acts like a little radiator) has devoloped a leak. Coolant is circulated through thee heater core(located in that area) when you turn on the heater. The core gets hot and a fan blows airthrough it and out into the cabin. A cracked or corroded core will allow coolant to escape into the heater housing and the fan will force it into the cabin. Hope this helps. Dano

Oct 20, 2011 | 1996 Chrysler Town & Country

1 Answer

96 CHRYSLER TOWN AND COUNTRY THE PASSENGER SIDE FLOOR IS SOAKING WET THE HEATER CORE IS ON DRIVER SIDE WHAT COULD BE LEAKING


heater core is actually centered behind controls- plumbing connections are on passenger side-look in engine compartment for leak first- loose clamp or split hose- then go to core- can try BAR's Leak first if not a hose problem

May 18, 2011 | 1996 Chrysler Town & Country

1 Answer

2005 Town & Chrysler heat is not working properly


check the hoses going to the heater core. if there is an extreme temperature difference you may have a heater core plugging up

Jan 26, 2009 | 1996 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...