Question about 1995 Suzuki Sidekick

2 Answers

Back up lights out, so many wires!!!!

The back up lights wont turn on and there wires loose but there are so many of them!! help!

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Expert
  • 43 Answers

Black: ground( all bulbs require a ground to operate)
green: right turn
yellow: left turn
red: brake
yellow and purple: back up

these are basic wiring colors they may not be exact for your aplication your best bet is to find someone u know with an ohm meter( multi meater) who knows how to test voltage and sort out the wires and re connect with splices NOT tape ur only asking for trouble if u dont do it right the first time ( oh before u start check the fuse size and get some extra u will probably blow a few sorting it out best of luck

Posted on Nov 05, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

As 95, well backup are just 1 wire. not lots.
is this a M/T car or A/T
on the A/T back up comes from the PRNL switch on the side of tranny.
if M/T 5 speed, its from the 5speed box , switch at rear of box.
the schematic is clear.
Turn-back fuse blow, (do turns work>?)
yellow wire leaves the tranny.
see page 4 (for front feed)
http://www.fixkick.com/power-elect/95%20electrics/95powersistra1.pdf
see page 6 here for rear feed.
http://www.fixkick.com/power-elect/95%20electrics/all-lamps95b.pdf

as you cans see, yellow, wire changes to red bad at the rear.
if 12v at rear, in reverse. try the yellow at tranny.
if no 12v there cut wires up front, if 12v good at tranny
only on input, then the switch at tranny is bad, if 12v good in and out
of said switch then wires are cut to the rear.
a $20 volt meter finds the fault. post to voltages measured, an it gets easier.

Posted on Apr 10, 2013

  • _-__-___-_
    _-__-___-_ Apr 10, 2013

    ****** WAS slang for transmission T r a n n y. wow, what prudism.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

? turn signal connector wires came loose only then wiper stop working + brake lights turn sig was searching for any help for wire diagram to get thing working again 2001 f150 its 7 wires, Thanks for a


Go to alldatadiy.com and buy the wiring for your vehicle. Other wise go to the junk yard and cut the plugs and wires out of an exact vehicle. This is the only two ways you will fix it. Exact diagrams or exact plugs and switches.

Nov 16, 2014 | Cars & Trucks

1 Answer

What does it mean when the car dies and wont crank back up


When this situation occurs, turn the ignition ON. You should hear the fuel pump, pump up to pressurize the system. If not, then look for a poor connection on the fuel pump and fuel pump ground wires. If you turn the ignition ON and the instrument panel lights, etc do not come ON, this points to a loose connection in the ignition circuit - maybe a faulty ignition switch.

Mar 27, 2014 | 2004 Oldsmobile Aurora

1 Answer

Pontiac montana wont start


sound like ignition switch going bad or have loose wire to ignition switch.

Jul 22, 2013 | Cars & Trucks

2 Answers

My headlights, hazard, turn lights, and my horn does'nt have power. help.


you may have messed up the module your lights are ran in parallel circuits so just in case you loose one light you wont loose both. so my next thing to check would be the control module or the swith. get a test light and check for power at the switch. if you have power their go to the headlights and check power their.

Jul 09, 2012 | Cars & Trucks

1 Answer

Dash lights wont come on and now the tail lights are out checked all bulbs and fuses all good what could be the problem


Check to make sure all grounds are hooked up and not loose had this problem on a chevy truck after it came back from the shop and the **** didnt hook up all the ground wires (wont be back there) behind the dash there was about 8 of them Hope this helps

Aug 07, 2011 | 1999 Dodge Caravan

1 Answer

Four wheel wont disengage. had switch for 4x4 set to 2wd and the light switched to 4wd while driving down the road and the four wheel drive engaged. Tried to switch from 2wd to 4wd and back but didnt...


if it is a turn knob that puts it in 4x4.then a wire under the truck is touching the exhaust pipe making it do this. I had this happen to mine. It will be 2 wires so they more and likely came loose.

Feb 12, 2011 | 2004 Dodge Ram 1500

1 Answer

I have no headlights on 1988 mustang gt turn signals brake lights and parking lights and dash lights all work but the head lights wont come on checked all fuses and relays there all good thanks


Check headlight lamps... then follow the wiring from the bulb connections back and make sure you're getting a good solid ground connection. It may have a loose, broken, severed grounding wire.. it's usually attached to the car body at some location not far from the headlights.

Oct 14, 2009 | 1988 Ford Mustang

1 Answer

Van wont start, battery is ok,lights come on ok.then you try to crank it over and everything goes dead? no lights no dash or dome lights all black. wait a few minutes lights come back on then turn key all...


The problem is a loose connection at your battery or the distribution block. This is normally the ground wire. Try tightening these connections and you should not have a problem. Or wiggle the wires.

Jun 23, 2009 | 2001 Nissan Quest

1 Answer

Back Tails/Loose Wire


Hi,

Initially, pls try:
  • determine exactly where the loose connection is;
  • if it is on the connector, unplug and clean the prongs and contact mates;
  • you could also try using an electric contact cleaner but manual cleaning is still best;
  • in some instances, you may need to scrape the prongs to ensure no corrosion;
  • in some instances, you may need to slightly bend the prongs so that they provide more pressure when plugged in.
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 29, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
1995 Suzuki Sidekick Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...