Question about 2000 Jaguar S-Type

1 Answer

When I turn on my car lights on my left tail light turns off and on brake light go on what can be happing

I TRIED UNPLUG THE HARNESS AND CHANGED THE bulbs and it's the same

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 14,036 Answers

Problem could be in the headlight switch.all tied in same circuit.

Posted on Nov 05, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: tail and brake lights out

Check fusebox.

Posted on May 20, 2009

SOURCE: brake light out

You've got a broken or disconnected wire somewhere. Get a multimeter & check you have voltage on both sides of the fuse. If that's good you know you've got juice running out to the tail light. Remove the bulb & check for voltage in the socket. Chances are you have 20 years of corrosion behind the socket & it's dirty. Either way, you problem is a disconnected or corroded wire.

Posted on May 26, 2009

  • 82 Answers

SOURCE: Where is the fuse box on a 1992 jaguar Xj6 soverign

There is a fuse box on either side of the driver and passenger footwells, and a small fuse box in the centre console. But if the taillights don't work, its probably just bulbs to replace

Posted on Oct 24, 2009

iambanshee74
  • 3489 Answers

SOURCE: 2003 jaguar S type R < the problem ! when

start by comparing these "new" ones to the old bulbs. alot of parts guys dont know european cars and think they have the answere for everything cause they work on chevys'. it sound like a ground issue back feeding through the circuits. why did you change bulbs? burned out and then the problem occured? let me know please

Posted on Dec 30, 2009

csmock132
  • 4669 Answers

SOURCE: 2004 x-type jaguar stuck in park after tail light

Check the brake light fuse. If you blew a fuse for a brake light, you won't have power to the shift interlock which allows you to move the shifter.

Posted on May 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 04 audi a8, whenever i turn the ignition on the lights come on but as soon as i put it in gear my left rear tail light goes out. anyone have an idea why that's happing?


Sounds to me like the brake light circuit is interfering with the taillight circuit. My guess is a bad ground connection for the taillight bulb or brake light bulb.

Nov 02, 2013 | 2004 Audi A8

2 Answers

I have 89 bronco 2 my brake lights turn signals both work my tail lights don't work have check fuse n blubs what might be the problem


The turn signals and brake lights use the same circuit and filament in the bulbs. The tail lights are on the other circuit which comes from the headlight switch.
Do you have power on the tail light fuse ?

Feb 25, 2013 | 1987 Ford Bronco II

2 Answers

Trailer light hook-up


If this DeVille is trailer-ready, there is a trailer harness fuse box with 10A fuses for tail lights (PPL wire), left turn/stop/tail lights (YEL wire), and right turn/stop/tail lights (DK GRN wire

Oct 16, 2012 | 2001 Cadillac DeVille

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

I'm trying to wire my 89 jeep wrangler to be towed useing it's existing lights.the turn signals both flash when right or left is on? I've tryed it under the dash with no luck now all the way...


If the brake and turn signal are on the same bulb than you can Orin straight wiring. If the brake and turn signal are on different bulbs than you'll need a wiring harness with a converter box. I'm pretty sure the wrangler has the brake and turn signal on the Same bulb so let's start with basic trailer wiring. The green wire on the trailer harness is for the right side turn and brake for the trailer. This wire should be attached to the wire on the vehicle that supplies power to the right turn signal/ brake light. The yellow wire is the left turn signal, brake light on the trailer and should be attached to the wire on the vehicle that supplies power to the left turn signal /brake light. The brown wire is the tail lights on the trailer and should be attached to either the left or right side wire on the vehicle that supplies power to the tail lights. The white wire is grounD and it is vitally important that this wire be attached to the vehicle in a manor that supplies a good ground. Failure to suppy a good ground will result in all kinds of funky problems with the trailerer lighting such as all the lights linking when the tail lights and turn signals are on at the same time. If you have any specific questions I will be more than happy to try and help. Good luck.

Jun 29, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

It was wired for a 4 wire flat trailer plug. the plug was ripped off and now there are wires coming from both tail lights and the drive lights on rear passenger and trailer dont work. Green, Black, brown/w...


You need to install a 3-2 wire converter. I suggest a CURT 56175 then
1.Using a test lamp, identify the corresponding wires in the harness for the left turn, right turn, tail lights and brake lights. 3. Temporarily remove the vehicle's negative battery cable from the battery. 4. Using wire taps, attach the input wires of the tail light converter to the corresponding vehicle harness wires identified in step 2 as indicated.
Converter Brown Wire: Tail Light Circuit Converter Yellow Wire: Left Turn Circuit Converter Red Wire: Brake Light Circuit Converter Green Wire: Right Turn Circuit
5. Locate a suitable mounting location for the ground eyelet on the vehicle near the converter on vehicle's frame or cross member.
And your ready to tow!

Mar 08, 2011 | 1999 Plymouth Grand Voyager

1 Answer

How to wire a 4 pin connector for a LED Tailgate bar into the brake lines on a 2000 dodge dakota without trailor plug


With both tail light lenses removed locate the black with yellow wires and the dark green with brown wires coming out of the brake/tail/turn signal sockets.

The black with yellow wire will be the running lights or tail lights and the brown wire from the trailer harness will attach to it.

The green wire on the trailer harness will be the right turn signal and will be attached to the passenger side tail light harness dark green with brown wire.

The yellow wire on the trailer harness will be the left turn signal and will be attached to the dark green with brown wire on the drivers side tail light harness.

The white wire on the trailer harness is the ground wire and will need to be attached to a good ground. Is it pretty easy to crimp an eyelet onto the end of the wire and use a self tapping screw to attach it to the body behind one of the tail light lenses.

Here is a trailer light/wiring article I have done in the past. It has a couple of good tips you may find useful.

http://www.hotspotoutdoors.com/forum/ubbthreads.php/topics/1425999/1/Trailer_Wiring_101

Oct 27, 2010 | 2001 Dodge Dakota

1 Answer

05 Chevy Colorado trailer harness right turn not working


you must check the connection where the truck harness meets the added trailer harness on the truck itself not the trailer harness.

Apr 04, 2010 | 2005 Chevrolet Colorado

1 Answer

How do you wire up a trailer harness to a 1999 Grand Voyager?


Your earth is bonding properly. Make sure you have a good bond that is fixed either to your chassis, with all rust, sealent and other cotings are removed frois should dolve your problem.m the fixing. Th

Jul 25, 2009 | 1996 Chrysler Town & Country

1 Answer

Wiring


starting at the tail light harness coming from the truck, brown wire is for tail lights, black is ground, dark green is right turn and yellow is left turn, the turn signal wires are also the brake light wires. that sounds weird but if you hit the brakes and turn one of the signals on the actual brake light will blink. hope this helps you.

Jun 26, 2008 | 2002 Chevrolet S-10

Not finding what you are looking for?
2000 Jaguar S-Type Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...