Question about Honda Accord

1 Answer

P0Z80 trouble code

Car just shifts hard into 2nd. I hooked scaner up to the car and found codes p0730 and p0Z80. Not sure how to go about fixing the shifter malfunction and incorecct gear ratio. Need help!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 14,036 Answers

Problem could be transmission range sensor or faulty shift solenoids.i would let transmission check it out using diagnostic equipment to check transmission shift solenoid the scanner will manual test solenoids see if they are working.and scanner will check transmission range sensor make sure transmission shifting in right gear.

Posted on Nov 05, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 88 Answers

SOURCE: 1994 nissan sentra shifting hard

change fluid in trans add lucas for trannys let me know if theres metal in the pan or if you have trouble tell fixya bout me ok

Posted on May 24, 2009

keeperoffire
  • 106 Answers

SOURCE: 2002 Dodge Caravan, Tranny would shift, DTC P0700, P0725

replace the input speed sensor to transmission and the wiring pigtail all are available at your chrysler dealer take your vehicle registration in to the parts counter so they have your vin # to get the right part and it is the front of trans by fluid linres to radiator.

Posted on Mar 08, 2009

  • 412 Answers

SOURCE: transmission codes:

I WOULD TRY REPLACING THE INPUT SPEED SENSOR..A DEFECTIVE SPEED SENSOR CAN CAUSE ALL OF THESE FAULTS..IT IS LOCATED IN FRONT OF TRANS ABOVE SOLENOID PACK..IT IS THE ONE CLOSEST TO THE ENGINE..IT SCREWS INTO TO TRANSMISSION..A 1 INCH SOCKET FITS IT..ALSO CHECK WIRING TO BOTH SPEED SENSORS..A SENSOR IS ABOUT 35 BUCKS,AVAILABLE AT YOUR LOCAL DODGE DEALER..GET A NEW ONE AND YOU'LL SEE WHAT IT LOOKS LIKE..FAIRLY COMMON PROBLEM..HAVE REPLACED LOTS OF THEM

Posted on Jul 07, 2009

  • 30 Answers

SOURCE: 2005 Pontiac Vibe having trouble shifting 1st 2nd code P2716 MIL

This is most likely due to a bad solenoid pack in transmission. You could have tranny serviced and see if it helps. Poor fluid condition makes valves stick in those.

Posted on Aug 14, 2009

  • 6 Answers

SOURCE: P0734 Gear 4 Incorrect ratio

USUALLY WHEN ITS AN INCORRECT GEAR RATIO ITS USAULLY A INPUT SESOR AND IF THAT DOESNT FIX IT THEN TRANNY

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix error code p0730 gear ratio incorrect


code p 0730 refers to incorrect gear ratio====causes --wiring---TR ( transmission range) sensor / switch---shift solenoids ---transmission mechanical fault
check wiring and harness connections for bad/ corroded points
replace the TR

Mar 19, 2017 | Ford Cars & Trucks

1 Answer

How i fix the p0730 and p0735 in range rover 2006


Possible causes of OBD code P0730
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Shift solenoids harness or connectors - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: The TCM has detected that the transmission is trying to mechanically shift to a lower gear than intended

Possible causes of OBD code P0735
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: P0735 is detected when A/T cannot be shifted to the 5th gear position even if electrical circuit is good.

Dec 24, 2014 | 2006 Land Rover Range Rover

1 Answer

P0218 p0730 p0742


It's normal that won't shift into 3rd and overdrive because you have transmission code it's a default mode
P0730 Incorrect Gear Ratio
P0742 Torque Converter Clutch Circuit Stuck On
P0218 Transmission Over Temperature Condition
you need to solve those codes first

hope it helps

Mar 31, 2014 | 1999 Chevrolet Cavalier

1 Answer

Need help on p0730,p0780. I have a 00 Acura TL 3.2


code p0730 refers to incorrect gear ratio.==causes --wiring--TR sensors/switch--shift solenoids--transmission mechanical fault
code p0780 refers to gear selection--shift malfunction====causes--wiring--TR sensor---shift solenoids--transmission mechanical fault.. have the shift solenoid checked out. Have a pressure test done on the transmission to check for internal damage.

Nov 12, 2013 | 1999 Acura TL

2 Answers

Traction control on chevy hhr 2006


The traction control and transmission shifting would involve the body computer more so than the engine computer.
Have you had the body computer scanned for trouble codes ?

Sep 03, 2012 | 2006 Chevrolet HHR

1 Answer

How to fix problem codes 730-733 laredo 2009


There is no one fix works for all on these code. Also you have left out the letter and one number of the code I assume these are P0730 and P0733, if so read on.

P0730 CHRYSLER - Incorrect Gear RatioPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Shift solenoids harness or connectors
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0733 CHRYSLER - Gear Ratio Error In Third GearPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Jun 27, 2012 | Jeep Grand Cherokee Cars & Trucks

1 Answer

2nd gear drops hard


Dear Madam or Sir,

this is a well known problem with the Audi-transmissions, we do have a lot of failures with them over here in Germany. ;)

There are some software updates available, in many cases this fixed the problem.

Another possibility is a faulty transmission speed sensor, this is causing the hard shift behaviour.

First you should see the dealer to check the transmission control module´s trouble code memory and to check if there is a software update available for your car.


Jun 25, 2010 | 2004 Audi S4

2 Answers

OBD CODE P0730 GEAR RATIO INCORRECT


have the same code on my 2002 jetta with 1.8t. pulled the tranny apart on the car from the side tranny cover and found only one set of really burnt up clutches. very easy to change. i also had that po730 code. car felt like wouldn't shift into 3rd 4th 5th. better than spending $2000 for a used tranny!!

Aug 10, 2009 | 1997 Volkswagen Passat

1 Answer

Eng light


my golf car give me p0730 as a dtc code saying incorect gear ratio

Jun 16, 2008 | 2001 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...