Question about 1966 Ford Mustang

2 Answers

Headlamp pull out nob broke so can't turn on head lights wondering how to repair

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 76 Answers

If just the silver bezel broke you can buy a new one and it snaps on like the other one did. So that way you don't have to replace the whole thing, but if the switch itself broke, then you'll have to buy a new one. Hope it helped!

Posted on Mar 23, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Replace the headlight switch

Posted on Jan 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Head lights wont turn off 06 h3 hummer


If you pull the headlamp relay in under hood fuse box, that should kill the headlamps until you figure out the problem? I don't know if relay could be faulty? I'd want to check relay wiring circuit for ground?
Your bcm grounds the coil side of headlamp relay in order to energize. I'm not saying bcm has a problem? The bcm receives input from headlamp/dimmer switch telling it the headlamp relay should be grounded. You might check for bcm or communication trouble codes.
26312760-dtx0paaksp2dudcj4ee0acfc-2-0.jpg

Oct 15, 2016 | 2006 Hummer H3

1 Answer

Why aren't parking lights working?


Park lamp fuse 20amp located in the under hood fuse box .DRL control module
Daytime Running Lamps (DRL) Control Module
Right of the steering column, behind the IP
Park, Sidemarker, Tail and License Lamps
Voltage is applied continuously to the PARK fuse to the headlamp and the instrument panel (IP) lamp dimmer switch through CKT 1340.
When the headlamp and the (IP) lamp dimmer switch is in the PARK or HEAD position, voltage is applied to CKT 9 thus activating the following lamps:
• The park lamps
• The side marker lamps
• The tail lamps
• The license lamps
The park/turn lamps are the only lamps that do not activate yet receive a current from CKT 9. The park/turn lamps do not activate because the voltage drop across the front side marker lamps is much higher than that across the turn lamp filaments Step
Action
Normal Result(s)
Abnormal Result(s)*

1
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
The following lamps light:
• The license plate lamps
• The taillight lamps
• The front side marker lamps (Domestic)
• The front parking lamps (Domestic)
The headlamp position lamps (Export)
Refer to Park Lamps Inoperative
Park Lamps Inoperative
Step
Action
Value(s)
Yes
No

1
Inspect the PARK LP fuse.
Is the fuse open?
--
YES - Go to Step 2
NO - Go to Step 3

2
Repair a short to ground in CKT 1340.
Is the repair complete?
--
Go to Exterior Lights System Check
--

3
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal R and ground.
Did the test lamp light?
--
Go to Step 7
Go to Step 4

4
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal O and ground.
Did the test lamp light?
--
Go to Step 5
Go to Step 6

5
Replace the headlamp/IP lamp dimmer switch. Refer to Headlamp Switch Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

6
Repair the following conditions in CKT 1340 between the PARK LP fuse and the headlamp and the IP lamp dimmer switch harness connector terminal O:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check
--

7
Repair the following conditions in CKT 9 between the headlamp and the IP lamp dimmer switch harness connector terminal R and S204:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check

Feb 18, 2016 | 1999 Pontiac Montana

2 Answers

The running lights and tail lights work but no headlights on my 1994 Buick Skylark Custom. What is wrong?


Hey Dan , do you have a volt meter ? Pull head lamp bulb , with lights on check for battery voltage on tan wire left headlamp an lite green right side headlamp ! If there is no voltage back track to headlamp switch , which means pulling the plastic cover from around the upper steering column ! check for battery voltage at the Orange wire in connector # 1 , that is voltage supply to the headlamp switch ! Power going in an no power coming out with the switch in the headlamps on position means your switch is bad !

Apr 02, 2015 | 1994 Buick Skylark

1 Answer

Head lights turn on and off when tilting steering wheel up and down


Contacts to headlamp/hi beam switch are bad. Needs to have steering wheel pulled to replace headlamp/hi beam stalk/switch

Feb 14, 2011 | 1998 Jeep Cherokee

1 Answer

Fdecarlo57@gmailinstalling head light bulb


Hello,
To replace the head light bulb of your 1999 chevrolet tahoe, please carefully follow the steps below:
  1. Turn off the Tahoe's engine and open the hood
  2. Remove the two pins on top of the headlamp assembly.
  3. Remove the outer pin by turning it outward and pulling it out.
  4. Remove the inner pin by turning it inward and pulling it out
  5. Pull out the headlamp lens assembly. Unplug the electrical connector,
  6. Turn the bulb counterclockwise to remove it. Install the new bulb into the assembly and rotate it clockwise to lock it into place.
  7. Plug in the electrical connector. Place the assembly back into the vehicle and reattach the pins. Close the hood.
Hope this information helped you. Take care and good luck

Jan 07, 2011 | 1999 Chevrolet Tahoe

1 Answer

How to change head lights


Hello and welcome. here is the headlight replacement instructions.

Open the hood.



Remove the fascia to tie bar push-in retainers (1).

  • Gently pull the top of the fascia assembly several inches away from the vehicle to release the radiator grille strap from the headlamp.
  • Place a piece of tape over the radiator grille strap to headlamp retaining clip to prevent scratching of the headlamp lens.
  • Remove the headlamp bolts (1, 2).



    Pull gently on the bottom outboard corner of the headlamp to disengage the lower rear headlamp retainer.

  • Remove the bulbs (2, 3, 4, 5) from the backside of the headlamp.
  • Remove the headlamp from the vehicle.

  • 2379f3f.gifd9c6d55.giffc562f4.gif2d89b70.gifa552625.gif

    Aug 30, 2010 | 2006 Chevrolet Equinox

    2 Answers

    How to change a left front turn signal bulb


    there are 2 plasic clips that hold the head lights in you need to pull both of them up and remove the head light then behind the other assembly there should be a plastic clip to push over to release the lower assembly

    Nov 07, 2009 | 1998 Chevrolet S-10 Pickup

    1 Answer

    Wat tools use to change head light bulb in a chevy equinox


    You will need basic hand tools.

    Headlamp Bulb: Service and Repair
    HEADLAMP BULB REPLACEMENT (EQUINOX)
    REMOVAL PROCEDURE
    1. Open the hood.
    90a07c3.jpg 2. Remove the fascia to tie bar push-in retainers (1).
    888ce48.jpg 3. Gently pull the top of the fascia assembly several inches away from the vehicle to release the radiator grille strap from the headlamp.
    4. Place a piece of tape over the radiator grille strap to headlamp retaining clip to prevent scratching of the headlamp lens.
    25ee555.jpg 5. Remove the headlamp bolts (1, 2).
    054ce4f.jpg 6. Pull gently on the bottom outboard corner of the headlamp to disengage the lower rear headlamp retainer.
    7. Remove the headlamp from the vehicle.
    INSTALLATION PROCEDURE
    985fba5.jpg
    1. Position the headlamp into the headlamp opening.
    e3187c6.jpg 2. Push the headlamp back into position until the lower rear retainer is fully engaged.
    e5916af.jpg 3. NOTE: Refer to Fastener Notice.
    Install the headlamp bolts (1, 2)
    Tighten the headlamp bolts to 2.5 N.m (22 lb in).
    4. Remove the tape from the radiator grille strap retainer.
    efd9aad.jpg 5. Position the fascia assembly and engage the radiator grille strap retainer into the headlamp.
    5a4fd4a.jpg 6. Install the fascia to tie bar push-in retainers (1).
    7. Close the hood.
    8. Check and adjust the front headlamp aim after the headlamp has been reinstalled. Refer to Headlamp Aiming.

    Oct 04, 2009 | 2007 Chevrolet Equinox LS New Cars

    1 Answer

    The headlamp on my 2002 fireBird won't open.


    i think under hood it has a manual crank or nob you can turn to raise and lower incase of a malfunction.your electric motor or a gear is broke in there.hope this helps...

    Jul 06, 2009 | 2002 Pontiac Firebird

    3 Answers

    Front light not working


    replace the headlamp bulb. I just had to replace both the headlamp bulbs in an '05 model. Neither low beam was working. You'll have to pull the whole headlamp assembly out, but they tell you exactly how to do it in the owner's manual. Hope this helps.

    Nov 19, 2008 | 2006 Kia Sedona

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    82 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    63661 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21986 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...