Question about Cars & Trucks

1 Answer

Bumper Looking for the bumper bar for my linear freeway???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

The best advice I can give is to ask them directly on their Facebook page...there's a link to it on their homepage: \http://www.silvercross.co.uk/...other than that there doesn't seem to be any other way of contacting them or any place that sells spare parts for them.

Posted on Nov 04, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the front airbag crash sensors located on a freelander 2 2009 please


On the frame behind the front bumper the bumper is actually a cover over a steel bar that goes across the front it's not like the oldin days when a bumper weighed as much as the car can I ask why are we looking for the air bag sensors?

Dec 13, 2014 | 2007 Land Rover Freelander

1 Answer

How to removing the rear bumper bar


Slide under the bumper and look on the back side of it. You will find the bolts that attach it to the body.

Aug 07, 2014 | 1999 Saab 9-5

1 Answer

Where is the airbag impact sensor on the fender


Not too sure but the last time i checked it was on behind the bumper on the reinforcement bar or bumper support that goes from one side of the frame to the other and i belief their was a recall on that.You could also ask your dealer for a diagram.

May 27, 2014 | 1995 Chevrolet Monte Carlo

1 Answer

How to remove bumper bar?


Hi
You gotta first remove the front bumper cover which is usually torx screws and clips. Grille needs to be removed too.
Once off the main crossmember will be bolted onto the chassis legs by four bolts each side.
Roger

Apr 29, 2014 | 2009 Volkswagen Caravelle 2.5

1 Answer

Nissan pusal rear bumper removal instructions


DIY, you need a repair manual. Your autoparts store, or filepeep.com if they have it, or try manualslib.com

Nov 16, 2012 | 1990 Nissan Pulsar

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

1 Answer

I need to know how the plates are called that hold the back bumper in place on the far sides of the bumper.the bumper is held on on the top and on the bottom directly but the sides are held to the body...


the rear bumper is attached with "Brackets", however, the real bumper is a steel bar, inside the bumper "cover". The bumper cover is a plastic cover that is visible outside and painted. I am not sure to which you are referring. Maybe your best bet would be to stop by a auto body repair facility and have them write you a free estimate for repair. That would list the parts needed. From there you can find the name of the part you are looking for and order it yourself.
If this was helpful please give it a thumbs up to help others.

May 31, 2011 | Suzuki Vitara Cars & Trucks

1 Answer

The stud(s)joining the plastic bumper bar have come away - how can I repair this.


They are not really replaceable, just find some self tapping scews and replace the plastic studs with these... it wont look like it did but if you get some smart looking screws it could look better...

Aug 30, 2009 | Nissan Pulsar Cars & Trucks

1 Answer

Romoving front Tow Bar...


Just have to remove the 3 bolts on each side of the bumper. Just move the rubber splash guards out of the way so you can see the bolts up under there. Make sure you use anti-seize compound on the bolts when you reinstall. You will probably have to adjust each side of the bumper bracket so it fits back on your Jeep, cause with the tow bar removed, there is a gap now.

Apr 08, 2009 | 1995 Jeep Cherokee

2 Answers

Nissan R34 CRASH BAR


when saying crash bar do you mean roll bar? or the front bumper support?

if roll bar, i believe it will fit with minor adjustments on the floorboard.

if the bumper support. i dont think so. the r34 has a slightly more square design on the front end and would not make for a good switch.

in theory if you can weld you can get anything to fit. good luck hope they put a skyline section up for ya...ya lucky bastard. youve got my dream car. have a nice day

Oct 18, 2008 | 1996 Nissan 300ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...