Question about Cars & Trucks

1 Answer

I have 320s mercedes front suspention drops over night but back shocks are solid

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 62 Answers

I would check the air ride control. try to spray soapy water over the lines and at the boots above the wheel.

Posted on Nov 04, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: AIR SUSPENTION WORKS ABNORMALY

a lot of info here:
Principles of Operation
The 4-wheel air suspension (4WAS) module commands changes in vehicle height that are necessary for both the load leveling and the vertical height adjustment features.
The 4WAS load leveling feature automatically makes adjustments in vehicle height so that the vehicle is always at trim height, and that constant front-to-rear vehicle attitudes are maintained over the load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle left and right sides for the 4WAS system are restricted to what can be reliably achieved with three height sensors.
The height adjustment feature has three vehicle heights within a two-inch span:
Kneel height — improves the ease of entering and exiting by lowering the vehicle one inch below the trim height in the front and rear when the vehicle ignition is in the OFF or LOCK positions and the vehicle is stationary.
Trim height — normal vehicle ride position; vehicle moves to trim position when the ignition is ON, when the transmission is initially shifted to DRIVE or REVERSE mode, when all doors are closed or when speed of more than 24 km/h (15 mph) is detected.
Off-road height — improves ground clearance by raising the vehicle one inch above trim height in the front and rear when the vehicle is at 4x4 low modes and the vehicle speed is less than 40 km/h (25 mph).
The 4WAS module uses the universal bus protocol, (UBP), module communications network for sending and receiving various signals with the exception of speed, information from the three height sensors, and the air suspension service switch. For additional information about UBP, refer to Section 418-00 .
The 4WAS system holds vehicle height when any door or rear hatch is opened. The system stores front and rear vehicle height the moment any door is detected open. The system then maintains this height regardless of the addition or removal of a load. The system returns to its commanded height when all doors are closed or vehicle speed exceeds 24 km/h (15 mph).


Vehicle Height Modes Ignition State Transfer Case Mode Speed or Speed Range Resulting Vehicle Height OFF 4x2, A4WD, 4x4 HI N/A Kneel (TRIM - 25 mm) ON and RUN 4x2, A4WD, 4x4 HI All speeds TRIM ON and RUN 4x4 Low Below 40 km/h (25 mph) Off-Road (TRIM + 25 mm) ON and RUN 4x4 Low Above 40 km/h (25 mph) TRIM OFF 4x4 Low N/A Stays at current position (prior to ignition transition)
Air Suspension Service Switch
The air suspension service switch signal is needed to wake up the 4WAS module. Without the module receiving this signal, the 4WAS system is inoperative at speeds below 24 km/h (15 mph) and will not react when the vehicle is raised or lowered. At speeds above 24 km/h (15 mph), the system will be active as if the air suspension service switch is in the ON position.
Vehicles without message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, a "CHECK SUSP" will appear in the RH corner of the instrument cluster.
Vehicles with message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, the message center will display "SUSPENSION SWITCHED OFF"
Air Compressor
The air compressor:

  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay, which is controlled by the 4WAS module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • has a single port drier that can be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the 4WAS module determines that lowering is required.
  • provides an escape route for pressurized air when system pressures exceed safe operating levels.
  • has a 1034 kPa (150 psi) internal relief valve.
  • is installed with the air compressor as a unit.
Air Spring
The 4WAS system has front and rear air springs. The air springs provide a varying spring rate proportional to the system's air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system's air. Increasing air pressure (compressing) raises the vehicle; decreasing air pressure (venting) lowers the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the 4WAS module command.
Air Lines and Fittings
NOTE: Apply a soapy water solution to the air lines to verify the location of air leaks. If the air lines are cut, ruptured or leaking, a service repair kit is available.
Nylon air lines with quick connect fittings connect to the air compressor and air spring solenoids. The compressor assembly output line is divided by the use of a fitting to supply the front and rear air springs. Fittings are also used to divide the air supply to the RH and LH air spring solenoids.
Air Suspension Height Sensors
There are two sensors used for the front suspension and one sensor used for the rear suspension. The sensors send a voltage signal to the 4WAS module. The output ranges from approximately 4.50 volts at minimum height (when the vehicle is low or in full jounce) to 0.50 volt at maximum height (when the vehicle is high or in full rebound). The sensors have a usable range of ± 45° compared to total suspension travel of 196 mm (7.84 in) at the front wheels and 240 mm (9.6 in) at the rear wheels. Therefore, the sensors are mounted to the suspension at a point where full suspension travel at the wheel is relative to the travel at the height sensor. The front height sensors are mounted to the frame and the links are attached to the upper arm ball studs. The rear height sensor is mounted to the frame and the link is attached to the rear lower arm ball stud.
When the height sensor indicates that the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the system. When the sensor indicates that the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the system to lower the vehicle to its trim height level.
Compressor Relay
A solid state relay is used in the air suspension system for compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the 4WAS module.
The compressor solid state relay is energized by the 4WAS module to have high current flow from the battery to the compressor motor.
4-Wheel Air Suspension (4WAS) Module
NOTE: The 4WAS module must receive a ride height adjustment calibration and must pass a pneumatic test when it is installed new or swapped.
The 4-wheel air suspension (4WAS) module controls the air compressor motor (through a solid state relay), all air spring solenoids, and provides power to front and rear height sensors. The 4WAS module also controls vehicle height adjustments by monitoring the three height sensors and other universal bus protocol (UBP) signals. The 4WAS module conducts all fail-safe and diagnostic strategies, and contains self-test and communication software for testing the vehicle and related components.

Posted on Jan 13, 2009

  • 72 Answers

SOURCE: I need to know how to replace my upper shock on my 99 Sunfire

THE ENTIRE STRUT MUST BE REMOVED AND THE STRUT MOUNT ALSO REMOVED TO REPLACE THE BEARING.. SPRING COMPRESSOR TOOL IS REQUIRED TO DO THIS.

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan liberty rear suspension touching tire


I think suspention is dameged when fast driving on off road drive. So check suspention bush or pump by specialist of suspention and shock absobar. Other think big aloywheel and tyre fit your liberty.

Jun 18, 2016 | Nissan Cars & Trucks

1 Answer

I have 320s 2001 car drops at front over night back is fine


looks like you air ride is leaking somewhere. you can check the lins by spraying soapy water on them.

Nov 04, 2012 | Cars & Trucks

1 Answer

Something is causing the back end of the car to sit several inches lower than the front end.


If the vehicle has air suspention in the rear it may have one of these problems. bad sensor- pump-air line- shock. you should take it to a qualified repair shop.

Jan 16, 2011 | 2002 Oldsmobile Bravada

1 Answer

I have a buick lesabre 2002 and my question is *is it normal that my rear air suspention is verry hard in whinter ???* if the car comes out from the heated garage it's OK but if it sits all night outside...


Yes this is normal. The oil in the shocks thickens just like motor oil, and their is not enough weight in the rear of the vehicle to give the shocks enough of a workout to heat up and loosen up

Dec 30, 2010 | 2002 Buick LeSabre

1 Answer

2004grandam when driving over bumbs clunking noise in the rear end


the noise u hear would be the suspention the cold weather cuases the shocks not to push back out properly larger springs would solve the problem or new shocks

Dec 07, 2010 | Pontiac Grand Am Cars & Trucks

1 Answer

I need to know how to replace my upper shock on my 99 Sunfire


THE ENTIRE STRUT MUST BE REMOVED AND THE STRUT MOUNT ALSO REMOVED TO REPLACE THE BEARING.. SPRING COMPRESSOR TOOL IS REQUIRED TO DO THIS.

Jul 28, 2009 | 1997 Pontiac Sunfire

2 Answers

Front left suspension went out.


do you mean the front shockabsorber some call it a strut.

Jun 26, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

2000 continental air suspention not working


have your shocks checked. air suspension provides ride height and shocks control bounce from road bumps

Jun 25, 2009 | 1997 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...