Question about 2009 Pontiac Torrent

Open Question

Where is washer pump relay - 2009 Pontiac Torrent

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

2009 buick lucerne washer pump not working changed pump and fuses are good


Before changing the pump did you test for B+ voltage at the pump and check the ground circuit . Jump B+ voltage to see if it runs ? Does it have the heated washer system ? How about the washer relay , did you check it ?
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER relay, the WIPER HI relay and the WSH relay that are all located in the under hood fuse block.

Dec 19, 2016 | 2009 Buick Lucerne

1 Answer

Windshield washer pump relay location


Try to trace the rubber hose to the washer spray on the hood.
That should lead you to the washer pump. The relay should be in that area. Sometimes it's with the fuses under the hood.
Hope this helps.

Mar 30, 2015 | Cars & Trucks

1 Answer

Washer fluid pump not working, fuse is good but can't find relay


The relay is INSIDE the wiper motor, and not replaceable. Check if you have power to the Blue/White wire, if you have power (while pressing washer button) and the black wire has no power (ground) , then the pump is bad. If no power when pushing the wash button, ground the Gray/Brown wire at the wiper motor, if the washer works, then the washer button may be bad. The button grounds the relay using the Gray /Brown wire.

Nov 30, 2010 | 2008 Ford F 450 Super Duty

2 Answers

Disconnect windshield washer pump 1984 oldsmobile toronado


Are you certain it's the pump that's hit the fan?

Check your fuses, usually located under the driver's side of the dashboard.

Using a test light, Probe each side of the fuse. If the fuse hasn't blown, you'll have power on both sides of the fuse.

If the fuses are ok, check that you have power TO the washer pump itself, when the wash switch is engaged.

If you've eliminated all of the above, go ahead and replace the washer pump. Find it in the resevoir, disconnect the wiring harness, and clamp off the feed line (so you don't become covered in smurf ****!)

The washer pump will usually pull out with a little effort - somtimes removal of a few clips/hold downs/bolts may be necessary.

Nov 30, 2009 | 1984 Oldsmobile Toronado

1 Answer

Front washer not working....fuse ok, pump ok, switch ok.....where i relay to check.


there is no relay just a pump that is probably bad or the switch itself

May 22, 2009 | 1997 Ford Explorer AWD

2 Answers

Washer doesn't work and I can't hear the pupmp motor working.


The windshield washer pump is part of the windshield wash reservior.
There is an electrical connector located on the bottom of the reservior.
That is the pump .
If the pump is not in the reservior. I would just trace the washer fluid lines from the sprayer on the vehicle back to the pump. The lines just might lead back to the reservior for the windshield wash solution. Then you will have confirmed the pump is in the reservior.

You may have to get a new reservior. The pump might not be seperate item, I am not 100% sure on that.

I also would double check the fuses and any relays related to the washer pump.

Finally, I would check the washer switch if you replace the pump and still is not working .

Good luck

Mar 31, 2009 | 2002 Chrysler Town & Country

1 Answer

1999 windshield washer pump relay


there is no relay is the same fuse for the wipers

Nov 29, 2008 | 1999 Jeep Cherokee

1 Answer

Wipers


Fuse #11 is the one to pull.
30A Runs Front Washer Pump Relay, Wiper Run/Park
Relay, Wiper Hi/LO Relay, Windshield Wiper
Motor, Rear Washer Pump Relay

Nov 21, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
2009 Pontiac Torrent Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...