Question about Dodge Cars & Trucks

1 Answer

Do i need to have my 2004 dodge intrepid anti theft code reset through a dealership if the heads and head gaskets were replaced? the entire top of the engine ws taken apart adn put abcl together.

The entire top of my engine was taken apart and put back together because the head gaskets needed to be replaced and the heads checked. everything was fixed and put back on new and now the car wont start, do i need to have the anti theft code reset since it wasnt anything electrical?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 62 Answers

I would disconnect the battery. removing both the positive and negative battery terminals. with both ends disconnected, hold the two terminals together for about 10 seconds. this will proform a hard reset on most chrysler vehicles. also, if this doesnt work, try turning the key to the on position, and then proforming the hard reset procedure.

Posted on Nov 04, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: cranks but no spark/start 4.7 v8 G.cherokee

A COMMON PROBLEM I'VE SEEN MANY TIMES IS THE CRANK SENSOR DISRUPTING COMMUNICATION WITH PCM. UNPLUG THE CRANK SENSOR AND CHECK FOR RESPONSE OF PCM. IF COMMUNICATION IS NOW POSSIBLE YOU HAVE A BAD CRANK SENSOR. IT'S A PROBLEM I'VE SEEN NUMEROUS TIMES. DOUBLE CHECK YOUR TIMING.

Posted on Sep 27, 2008

  • 1596 Answers

SOURCE: there is this 2000 dodge intrepid that has a blown head gasket

It has been My Experience that Most Repairs on this Vehicle ARE PRICEY and it is Not Worth the Maintnance Cost For Instance To Replace the STARTER One Must Remove the Engine Mount This tacks On an Axtra 80 Dollars to Lobor To Replace The Engine Labor ALONE is Around 1,500.00 Cmopared to 6-8 Hundred on Most other Makes & Modles I Personaly Would NOT own One.

Posted on Feb 21, 2009

  • 57 Answers

SOURCE: steam and water coming out of my exhaust

Sounds like a cracked cyllinder head

Posted on Aug 26, 2009

  • 468 Answers

SOURCE: I need to replace the head gasket on my 2000

Normally I would advise exactly how to do a job, but this is one of those tasks that you NEED to buy a haynes manual so you have the correct tightening/torquing sequence, the correct method to set the timing, etc. This can be an involved process, and without the proper illustrations and information, would be homocide to your vehicle's engine to undertake. While you're in there, you'll want to change out the timing chain as well though, FYI.

Posted on Oct 22, 2009

  • 1 Answer

SOURCE: how to reset factory anti theft system dodge intrepid

how to reset the anti theft system for my 2006 dodge ram 1500

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Why is water getting in my oil in my motor?


I think you blew a head gasket or broken head this is a big proble n costly did u get it hot n does it start n if it start will it run good because if it start n runs good it could be the intake gasket that why water mixing with the oil but n if it doesn't start or it start n run fought you have a bad head gasket or broken head good luck

Oct 03, 2015 | Dodge Cars & Trucks

1 Answer

2001 intrepid 2.7l engine, anti freeze is getting into oil.


This most likely means the head gasket has failed and must be replaced. If so, it's bad news because that is an expensive job........not the parts, but the labor. It involves removing the head, putting on a new head gasket, and then cleaning that mess out of the crank case if you have been driving it that way very long.

Dec 25, 2010 | 2001 Dodge Intrepid

1 Answer

Keeps blowing out coolant from over flow and fill tank


Could be as bad as the Head Gaskets, or as easy as needing to 'burp' the coolant system. Was the cooling system touched recently? Such as replacing thermostat or anti-freeze/coolant? If so, the system probably needs to have all trapped air removed - called burping.

If there's any oily residue in the coolant or over flow tank, than the head gaskets are most likely bad. Call your mechanic.

GL,
Td

Sep 10, 2010 | 1997 Dodge Intrepid

1 Answer

What would cause overheating after 15 to 20 minutes of driving?


CHECK COOLANT LEVEL FIRST BUT IT SOUND LIKE FAULTY THERMOSTAT OR LEAKING HEAD WILL ALSO CAUSE OVERHEATING WHILE DRIVING.I WOULD REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP FIRST.THAT WAY YOU KNOW IF HEAD GASKET LEAKING.CHECK ENGINE OIL IF IT LOOKS LIKE MILK SHAKE HEAD GASKET BLOWN.

Jul 25, 2010 | 2004 Dodge Intrepid

1 Answer

99 Dodge Intrepid 2.7L no power to ignition. Receiving Code P1684 but battery connection okay.


I have a problem with a 1999 Dodge Intrepid 2.7. Looking for some help or suggestions.


Problem: I only have a spark from the #2 coil.


Background:


Vehicle purchased from an Auction and would not start. The vehicle would only backfire. When I removed the valve covers I found that one of the rocker arms had popped out. I replace the heads with heads from a 2001 Intrepid 2.7. I used the cams, primary and secondary timing chains from the 1999 heads. Not sure if I used the original primary (left) cam sprocket from the 1999 or one I purchased in a kit from a Dodge dealership. I tried to use the new primary timing chain but it was not the same. The replacement heads were surfaced and a new head gasket was used. When I tried to start the vehicle it had no spark. The vehicle had set at several locations and parts may have been removed or changed.


Solutions Tried:


I tried 4 ASD relays with no effect. I then tested all 4 on a 2002 Intrepid 2.7 that runs and all worked. I then discovered that the Crank PS has missing. I replaced the Crank PS with one from a 2002 Intrepid 2.7 with no effect. I then replaced the Crank PS with a Crank PS from a 1999 Intrepid 2.7 and got a spark at the #2 coil only. I then replaced the PCM and TCM from the same 1999 Intrepid I got the Crank PS from and still only have spark from #2 coil. I then changed the Cam PS, still spark only from #2 coil. I have tried several coil packs on connector #2 and all have spark. Each coil pack that sparks on #2 will not spark on any other connector. Spark from #2 coil is weak.


I then replaced the wire harness from the PCM to the coils and fuel injectors and still only have spark from the #2 coil. What am I missing? Any suggestions, advice or related information will be greatly appreciated!


Thanks!

Keith P. Richardson

Kpricha2@yahoo.com

404-606-0728

May 20, 2010 | 1999 Dodge Intrepid

2 Answers

How to reset factory anti theft system dodge intrepid


how to reset the anti theft system for my 2006 dodge ram 1500

Oct 19, 2009 | Cars & Trucks

1 Answer

GREY SMOKE AT START UP AND AT HIGH IDLE


Sniff the exhaust, does it smell like oil or antifreeze? If so, replace the head gaskets

Oct 06, 2009 | 2004 Dodge Intrepid

1 Answer

Replace a head gasket for a 2002 intrepid


go to the parts store and get a chiltons or a haynes manual

Aug 13, 2009 | 2002 Dodge Intrepid

1 Answer

Do my 2004 dodge intrepid have a kill switch?


Your dodge has an antitheft system that shuts down the ignition and fuel system when the lock was tampered with. This is why they did not take the car your anti theft system did exactly what it was designed to do. You will need to get it to the dealer to get the system reset.

Mike

Jan 07, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...