Question about 1999 Mercury Sable

1 Answer

P0113 code - 1999 Mercury Sable

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 62 Answers

Po113 codes on all fors is a idle air temp sensor. i would check the sensor which is located before the throttle body.

Posted on Nov 04, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 300m brake, abs, trac off lights on with P0113 code


Intake air senor, did you plug it back in. On the plenum between the air filter and throttle body. They rarely go bad. If plugged in , check for a broken wire right behind the plug. they break inside the coating.

Jul 07, 2015 | 2002 Chrysler 300M

1 Answer

2004dodgeram1500 4.7l engine codes p0300 p0304 p0113 p0344


Hello Anonymous,maybe you can read this PDF ,it can help you,
Diagnostic Trouble Code Table .

Apr 04, 2014 | 2004 Dodge Ram 1500

1 Answer

Replaced the MAF. Still have the P0113 code. Car runs fine. Cannot find another intake air temperature sensor anywhere on the vehicle! Where is it?


code p0113 does not refer to a MAF sensor so replacing that was a waste of money=== It refers to intake air temperature (IAT) sensor---circuit malfunction====causes --wiring open circuit/short circuit to positive--wiring short circuit to ground---ground wire defective---IAT sensor---ECM.
Replace the IAT and check the wiring is in good condition and the connectors are clean and tight.

Jan 25, 2014 | 1999 Ford Explorer

1 Answer

Codes p0203, p0123, and p0113 are showing for my 2001 jeep grand cherokee. The voltage from the tps plug was 1.5v


P0113 intake air temp voltage too high
P0123 Throttle position sensor voltage too high
P0203 is injector #3 control circuit
voltage is higher that 4.9 volts short to 5 volt supply circuit

erase the codes and drive vehicle to see if the codes come back if they do you have a hard code check the supply circuit for a short

Nov 11, 2013 | 2001 Jeep Grand Cherokee

1 Answer

P0113


P0113 - Intake Air Temperature Circuit High Inputxicon.jpghttp://engine-codes.com/p0113.htmlForum CodePossible causes- Dirty air filter
- Intake air temperature (IAT) sensor harness is open or shorted
- Intake air temperature (IAT) sensor electrical circuit poor connection or sensor has been disconnected in error
- Faulty intake air temperature sensor When is the code detected?- An excessively high voltage from the sensor is sent to ECM.

Aug 08, 2012 | Cars & Trucks

1 Answer

Code P0113-P0183


DTC P0113 - Intake Air Temperature Circuit High Input.The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.


DTC P0183 - Fuel Temperature Sensor Circuit High Voltage.


I suggest to check wire connections.

Apr 13, 2012 | 2005 Nissan Quest 3.5

1 Answer

P0113 is what is stated on the service code. what does it mean?


P0113 -

Intake Air Temperature Circuit High Input

It looks like it is related to the IAT sensor or circuit.


For more info, go to this web site/link:

http://www.obd-codes.com/p0113

Jul 09, 2011 | 2005 Ford Escape

1 Answer

What is code p0113 repair procedure


CODE PO113 IS THE INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH INPUT.

Jun 10, 2010 | 2001 Ford Windstar

1 Answer

Engine code p0113


intake air temperature sensor disconnected

Sep 20, 2009 | 2003 Dodge Durango

Not finding what you are looking for?
1999 Mercury Sable Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...