Question about Cars & Trucks

Open Question

Manual seat on crown vic, how do you deflate lumbar

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 23 Answers

SOURCE: driver's side lumbar support in 05 pacifica seat won't inflate

there is a relay that controls the lumbar its under the seat unbolt seat replace the clicking relay

Posted on Dec 24, 2008

Ad
  • 7 Answers

SOURCE: The Lumbar support adjustment fails

I wonder if you dont have a bad switch. I had a similar problem on my car except that it was the heated seats that would not engage... the power seat buttons all worked just fine. I changed the switch and it fixed the problem...

Note: this was on a BMW not a Murano

Posted on Dec 31, 2008

  • 5546 Answers

SOURCE: Wiper motor replacement for a 99 crown vic

I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

Posted on May 06, 2009

  • 33 Answers

SOURCE: Replace horn on 2006 crown vic

I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you

Posted on Jul 04, 2009

  • 262 Answers

SOURCE: 1996 crown vic pi abs light on. can i pull codes

No you must have a scan tool

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lumbar on the driver seat does not work an the switch is stll good what could be wrong


lumbar on the driver seat Shawn, Its cable driven plastic plate. It can possibly be repaired once you disassemble it and can see it, if not repairable you can replace the lumbar. Check the attached links,forums with instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Thread Town Car Lumbar motor assembly replacement

Power seat lumbar support repairs

Drivers Power Seat Just Stopped Working Lincolns OnLine Message Forum

Apr 08, 2016 | 2007 Lincoln MKZ

1 Answer

Lumbar seat for 2006 trailblazer will not deflate


could be a problem witch air solenoid inside the seat or the balloon itself or line not connected
hope it helps

Mar 27, 2014 | 2006 Chevrolet Trailblazer Ext

1 Answer

I have a 2001 Ford Crown Vic. I replaced the seats with 2002 seats. The air bag light is now on. The plugs are identical. Help


hope you saved the old seats.test your old sensors with a ohm meter then test the new seat sensor to see if they test the same.if they don't you will have to swap out the sensors

Feb 16, 2013 | 2001 Ford Crown Victoria

1 Answer

Seat's are stuck


you said seats so I am assuming you mean 6-way driver and passenger. You also say you looked at all (my) fuses but actually the seats are controlled by 20A circuit breaker 7 in the battery junction box. If certain functions don't work, it may be due to failure of the seat adjust switch or lumbar adjust switch or any of the five adjusting motors

Oct 17, 2012 | 2002 Ford Crown Victoria

1 Answer

How to repair the lumbar support in a 2010 sebring


The manual support linkage has become disengaged or may have broken. Check to see which is the case and make repairs

Sep 17, 2012 | 2010 Chrysler Sebring

1 Answer

Front seat of 1993 crown vic is loose or broken


look under seat and u will ee the rails on each side of seat rock seat back and forth to locate wich bolt is loose or broken or if the rail itself is broken if rail broken remove the seat and order or go to a junkyard for the rail

Mar 02, 2012 | 1993 Ford Crown Victoria

1 Answer

The Lumbar support adjustment fails


I wonder if you dont have a bad switch. I had a similar problem on my car except that it was the heated seats that would not engage... the power seat buttons all worked just fine. I changed the switch and it fixed the problem...

Note: this was on a BMW not a Murano

Dec 31, 2008 | 2005 Nissan Murano

1 Answer

Driver's side lumbar support in 05 pacifica seat won't inflate


there is a relay that controls the lumbar its under the seat unbolt seat replace the clicking relay

Dec 24, 2008 | 2005 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...