Question about 1997 Lincoln Continental

1 Answer

Transmission wont engage in OD,D ,2,1. Goes in reverse normal.

Stoped at light and the car acted like i put it in neutral but I didnt. I backed into a parking lot. Checked fluid level, ok, took battery cable off for 5 min. put it back on, no change.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Best thing to do is check the fluid condition, dark or burned smelling fluid would indicate the clutches are worn out. The problem may also lie within the vvalve body, if for some reason the connection to the spool is damaged, it could only work when shifting into reverse. I try to make this may standard answer when it comes to transmission. Let a professional look at and repair, they are very complicated.

Posted on Feb 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHILE DRIVING


10 Most Common Transmission Problems

www.transmissionrepaircostguide.com/10-common-transmission-proble...
Ever notice that while driving that the car hesitates or refuses to go into gear? ... For automatic transmissions, you might notice that when shifting into drive or park ....Neutral and park gears no problem, but drive, 1st, 2nd and reverse engages ...

Trans Goes Into Neutral While Driving - Transmission ...

www.transmissionrepaircostguide.com/topic/trans-goes-into-neutral/
Jun 5, 2015 - When I put it in drive, and begin to drive away the transmission will put itself in neutral. When I slow back down, it will go back into gear.

Jan 13, 2016 | Cars & Trucks

1 Answer

Eclipse goes into reverse but wont go in drive.


Friend, start the engine and let it run a few minutes to warm the trans fluid, set the park brake or block the front of the wheels, put the car in drive position and check the transmission fluid. Sounds like it's just too low for the pump to pick up enough for a forward engagement. Reverse doesn't take much to activate the servo. Most automatics are this way. I'm sure you'll find the fluid is way low and needs the proper fluid added. This may mean you have a slight trans fluid leak.

Apr 04, 2017 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Mitsu 3000GT Auto Transmission


Im having the exact same problem, word for word, with my 1995 3000gt! Anyone have any ideas on how to fix it please???

Feb 09, 2012 | 1995 Mitsubishi 3000GT

3 Answers

I changed the gear box of my 2007 corolla about 5 months ago. Then I noticed the car jerks or kind of pushes forward whenever i change my gear from park/neutral to drive or reverse. Please what do you...


A delay of more than a second in shifting from the neutral to drive or reverse gear, could mean that there is a problem with the transmission. If on changing from a neutral or park position to the drive or reverse gear, the car does not immediately catch the gear and move forward or backward, then it could mean a problem in the transmission. If you change gears, and you hear a sudden clunk or sudden jolt or shudder, then the shifting is not smooth and there could be a problem with the gearbox. If the engine rpm keeps increasing but there is no increase in the speed, then it could be a sign of the transmission slipping.Most automatic transmission systems, nowadays, have a check engine light or an OD light, which flashes if there is a problem with the engine.

Oct 01, 2011 | 2007 Toyota Corolla

1 Answer

Transmission will not shift into overdrive on a 2003 4.7L Jeep


This will not repair the problem but it will cause your OD to shift. Caution: you need a long stretch of highway and sparse traffic.
After trying everything I could think of, I noticed that when the automatic locks failed to engage (at around 15mph) that's when the transmission would not shift into OD. So, now when the locks don't lock and the transmission doesn't shift to OD, I put the transmission in neutral and turn off the ignition and let it coast to a slow speed (see above caution). When I start the engine again and put the transmission back into drive, the locks engage and so does the OD. Works for me. I'm currently doing research on what causes the locks to engage automatically. I'm thinking it will be a vacum or a switch. BTW, mannually engaging the locks will not work. Good luck. Hope it works for you.

Jan 12, 2011 | 2003 Jeep Grand Cherokee

1 Answer

How to shift into 4 LO in 2004 jeep grand cherokee


The correct procedure should be described in detail in your owner/operation manual.
For a 2004, 90 % sure that if it's a quadra trac you have to immobilize the vehicule, put your transmission shifter to neutral keeping foot on the brake obviously, engage the low on transfer case pulling the transfer case shifter, engage the transmission to drive
If it's a select track, normally you have to keep the vehicule moving very slowly (2 mph), move the transmission shifter to neutral, push the transfer case shifter to the right and pull it firmly. Once transfer case engaged, put back the transmission shifter to drive.
It could take few seconds to engage and disengage depending on the temperature and road condition. Do not try it on dry surface (preferable on mud, snow and wet surface). Drive at low speed because you will feel that it's very low geared.
By the way, follow the reverse process to reestablish normal mode

Hope it will help
Dan

Dec 21, 2009 | 2004 Jeep Grand Cherokee

2 Answers

Backup lights do not work...1987 325ic...new bulbs installed, all other lights work perfectly...in reverse, with lights on, backup lights do not come on. Where is the backup light switch? There is a set...


it depends if it is auto or manual. There is a nuetral saftey switch on the auto-located on the manual valve arm(the piece that the linkage from the shifter connects to at the trans.) On the manual trans. there will be a 2 pole switch on the top shift plate that is for reverse only. The starting(clutch engagement switch)is located at the clutch pedal-2 seperate switches. First check for power at the back up light bulb connecter with reverse engaged(may have power at all times when key is on). Then check for ground when reverse is engaged-from bulb connecter to ground) with reverse engaged. The switch will just provide the ground when reverse is engaged. The power comes from an alternate source. Most likley a switch issue but at least this way you can be sure.

Aug 09, 2009 | BMW 325 Cars & Trucks

1 Answer

OD on Auto gearbox goes into neutral when cold


You need to have your transmission serviced. The fluid has gotten so thick in there that it builds up too much pressure and your transmission will either kick it out of gear or blow up. I'm glad it actually still works. Once the oil warms up it thins right out and it works no prob. Just service your tranny, and you'll be fine.

Hightower

Apr 12, 2009 | 1997 Mitsubishi Galant

2 Answers

1991 Caprice No reverse. Moves in neutral. All forward gears OK.


shift linkage needs adjusting,,could be bent, easy fix, located along firewall to fram beneath the column, ask your son wut he ran over and didnt tell u about... hope i could help...:)

Mar 22, 2009 | 1991 Chevrolet Caprice

2 Answers

1991 Caprice No reverse. Moves in neutral. All forward gears OK.


What engine? Rear wheel drive ?Sounds like shift linkage or cable out of adjustment slightly. Have a look at where cable or rod attaches to transmission for adjustment. If not sure of what your looking for get back to me with info.

Mar 21, 2009 | 1993 Nissan Maxima

Not finding what you are looking for?
1997 Lincoln Continental Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...