Question about 1999 Dodge Dakota

Open Question

Where is turn signal flasher located on 99 dakota

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: flasher on a 2002 dodge durango

Have you check in fuse panel for a round or square (1" roughly) piece?

Posted on Dec 13, 2008

RudolfDiesel
  • 100 Answers

SOURCE: flasher location for signals

Hello
Welcome to FY
It is located on the drivers side, at the left side of instrument panel located on fuse block. It simply unplugs. They are usually round about the size of a silver dollar with 3 plugs. Can be plastic or metal
RD

Posted on Jan 12, 2009

  • 1779 Answers

SOURCE: location for turn signal flasher

It's behind A/C + heater control panel to right hand side of the steering column. Curt

Posted on Apr 26, 2009

polarcycle
  • 1392 Answers

SOURCE: 2000 dodge dakota quad cab turn signal problems, but flashers work. started out the turn signals would flash several times then quit. now i have nothing.

Either a multifunction switch, or a body control module problem. Possibly the flasher itself.

Posted on May 12, 2009

  • 104 Answers

SOURCE: i have a 2001 dakota turn signals are flashing

check grounds then signal switch-oh but dont forget dodge have a body computer that controls all lights fron the switches with on-off or resisted signals-my advice go to a dodge repair outlet,will save you time and money

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where the hell is the turn signal flasher located on a dodge Dakota 2005


Does not have one. It uses the instrument cluster and the integrated power module to run signals and generate indicator noise.

Feb 28, 2015 | 2005 Dodge Dakota Quad

2 Answers

How do I find the location of the turn signal flasher on my 2002 Dodge Dakota?


Should be on the fuse box under the instrument panel.
Check your owners manual for details.

Feb 22, 2015 | 2002 Dodge Dakota Club Cab

1 Answer

1998 Dodge Dakota need to locate the signal light flasher, hazard light flasher also no break lights.


the signal light flasher & hazard flasher are located where your fuses are.

Sep 09, 2014 | 1998 Dodge Dakota

1 Answer

Blinker on 1998 dodge Dakota don't work but flashers do replaced blinker switch


Most likely this is the result of a faulty turn signal flasher relay. This is located in the fuse box at the end of the dash. Also, be sure and test all your fuses with a test light or volt meter.

Dec 24, 2010 | 1998 Dodge Dakota

1 Answer

I need to replace my 99 mercury mountaineer electronic flasher for my turn signals and can't find it to replace it


The signal flasher is located on/near the steering column. Revove the cover that is located between the steering wheel and the insturment panel. The Flasher is yellow

Sep 24, 2010 | 1999 Mercury Mountaineer

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

1 Answer

Turn signals wont work but flashers do


Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Aug 31, 2008 | 1998 Dodge Dakota

Not finding what you are looking for?
1999 Dodge Dakota Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...