Question about 2000 Audi S3

Open Question

17947.p1570 clutch switch - 2000 Audi S3

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1570 communication with transponder missing.


OBD2 fault codes go by make the first digit is a "1", so go here and look it up for your make. If you need more help comment back
http://www.obd-codes.com/trouble_codes

Jul 03, 2016 | Cars & Trucks

1 Answer

I have a 2000 Mercedes SL500. Cluster is flashing 'start error' and I have a P1570 code. Engine cranks but won't start. Starter has an abbreviated spin time too


code p1570 refers to ignition switch control module/ECM-attempted theft/data bus/not compatible ===causes --wiring--connections--trouble codes stored in other system--ignition switch control module---ECM
If this is a recent problem I would suggest that the ignition switch module be checked/replaced.

Nov 03, 2014 | Mercedes-Benz Mercedes Sl 500 Class Sl500...

1 Answer

17978 p1570 engine control module disabled


have you had the codes reaset ? if so then i'd think your looking to get the eng control module changed

Oct 15, 2014 | Cars & Trucks

1 Answer

P1570 Honda Accord Hybrid


well, you bought a car that takes a NASA engineer to keep going
so take it to the man.?
if really feeling safe working any HV car. (high voltage)
I am but are you? DIY?
then buy the FSM and read, it , then ask questions.

join the honda hybrid forum. ask there..... vast hits on same.
zero here.

Jan 08, 2014 | Honda Accord Cars & Trucks

1 Answer

Volkswagon Golf 1.9 tdi fault code P1441


Go here:

http://www.obd-codes.com/trouble_codes/volkswagen/

Jun 06, 2012 | Cars & Trucks

1 Answer

What does it mean code p1570


It means that your car will not start because the immobilizer has been activated.

Feb 16, 2012 | Volvo Cars & Trucks

1 Answer

Giving code p0704


P0704- Clutch Switch Input Circuit Malfunction

Possible Causes:
- Open or short clutch switch circuit
- Poor clutch switch circuit connection
- Damage clutch switch
- Misadjusted clutch switch
- Damaged ECM

Possible Solution: Check clutch switch adjustment, the switch should open and close when the clutch pedal is depress. If the switch is properly adjusted, replaced the clutch switch to resolve problem.

Aug 26, 2011 | 1998 Dodge Avenger

1 Answer

The car wont start sometimes and sometimes it will. The engine doesn't even turn over but it's not a battery problem because we had that checked. What could it be?


Dear Madam or Sir,

this is a well known problem with the immobilizer system.

See the following official tech bulletin :

Affected vehicles:
All models with Bosch RB8 instrument panel up to 2002 MY.


Problem:

Engine starts and cuts out immediately.

Trouble code stored: 17978 (P1570) - engine control module (ECM), immobilizer active.

Trouble code stored: 18058 (P1650) - CAN data bus, instrumentation - no signal.


Cause
Immobilizer fault.
System arms when ignition switched ON.

Remedy:
Access fault memory. If trouble codes present fit modified instrument panel (incorporating immobilizer control module).

Note: Immobilizer can only be programmed using diagnostic equipment.



Jun 26, 2010 | 2000 Volkswagen Golf

1 Answer

I have engine codes p1557,& p1570 set on my 2001 jetta tdi.what do i need to fix.


P1557 is an overboost condition, poss. from sticky vanes or actuator in the turbo. P1570 is due to your immobilizer being tripped somtime in the recent past. As long as the car still starts and doesn't shut off a few seconds later this poses no problem

Apr 25, 2009 | 2001 Volkswagen Jetta TDI

2 Answers

Clutch check


you have civic SI type R with the K20A engine and 6sp transmission? correct?

yes the clutch is adjustable.

  1. loosen the clutch pedal position switch(lower of the 2 switches) locknut and back off the clutch pedal position switch.
  2. loosen the clutch push-rod locknut and turn the push-rod in or out to get the desired height and stroke of the pedal.
  3. tighten the push-rod locknut
  4. with the clutch pedal released, turn the clutch pedal position switch in until it contacts the clutch pedal.
  5. turn the clutch pedal position switch in an additional 3/4 to 1 turn.
  6. tighten the clutch pedal position switch locknut.
  7. loosen the clutch interlock switch(the upper switch) locknut and then the interlock switch.
  8. press the clutch pedal to the floor.
  9. release the pedal about 1/2 in. from the fully depressed position, and hold it there. adjust the position of the interlock switch so that the engine will start with the clutch pedal in this position.
  10. tighten the interlock switch locknut.
clutch pedal stroke should be: 5.1 - 5.5 in
clutch pedal height should be: 7.76 in

if adjusting the clutch doesn't help with the transmission feeling notchy, may be the syncros.




Jul 09, 2008 | 2002 Honda Civic

Not finding what you are looking for?
2000 Audi S3 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...