Question about 2006 Hyundai Tiburon 2.0

Open Question

How to remove a toyota auris rear light cluster

I need to change a broken toyota auris rear drivers side plastic light cluster, but only got as far as removing the jack

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Richie_asg1
  • 1036 Answers

SOURCE: replace driver side rear light

Hi,
Most are held in from inside the vehicle with clips or very few screws.
You would need to remove any carpet trim first - and be careful of sharp edges.
the "press stud" type fixings can be removed easily without damage by sliding a fork or two blunt knives either side to lever them out.

Posted on Jan 03, 2009

mastertecmec
  • 42 Answers

SOURCE: replacement of 2003 hyundai sonota instrument cluster

Removed the dash bezzle and low and behold there were the screws to remove the dash cluster

Posted on Jan 27, 2009

  • 59 Answers

SOURCE: I need to replace broken driver side door handle.

In the auto glass trade there are very basic tools used. Most door panels are held on with a few hidden screws - behind latch handles under them, look any where that the door receiveds pulls or pushes. after all the screws are out 4-6 then the panel will either lift straight up to come off or pull straight out if it comes out then there will be some push plugs also holding that hold the panel in place and you could use a flat forked pry bar to pop them loose. Just take you time and you should be fine.

Posted on Feb 23, 2009

  • 57 Answers

SOURCE: Need to remove rear wheels

Hi sounds like  you got the alloy wheel corrosion problem although it sometimes affects steel wheels make sure the car is adequately supported, then you need a large rubber mallet to bash the wheel rims off. if you havent got a mallet then use a normal hammer but with a piece of wood between wheel and same. on no account hit the wheel directly with the steel hammer!

Posted on Mar 30, 2009

  • 2 Answers

SOURCE: how to change hyundai getz brake light in light cluster?

On the Getz remove 2 screws on the outside then gently prise the cluster off from the dowels as above.

Posted on Aug 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change language from Japanece to English on Toyota Auris 2008


You would use the Display button on the left side of the instrument cluster, though it is going to be difficult if you don't read Japanese as I haven't found any information on that part.

Feb 03, 2017 | Toyota Auris Cars & Trucks

1 Answer

How do you change the rear tail light bulb (passengers side)?


find the socket on the inside then turn and pull the bulb out .

Oct 19, 2015 | 2007 Toyota Auris 2.0

1 Answer

Rimove the rear bezel from toyota auris


Need more information! Not sure what you mean by bezel?

Feb 04, 2014 | 2007 Toyota Auris 1.6

1 Answer

Replace Right Rear broken Taillight assembly


Just joined 20 minutes ago....maybe I can help.
My volkswagen golf rear cluster is often a bother.
1, Open boot area and remove the plastic cover.
2, Often its the 3 or 4 nuts holding the interior cluster in place, use a socket to remove them, a 8/10/12 mm nut usually .
3, Exterior shell falls away, allowing access to the bulbs.
4, reverse to re assemble.


Good luck, Dave

Apr 02, 2013 | 2008 Toyota Highlander

2 Answers

My Instrument Cluster is not working or illuminating, Fuel, Speedometer and RPM gauges all not functioning


First thing to do is make sure your dimmer switch is turned all the way up to high. Next thing to do is check the instrument cluster fuse located underneath the drivers side steering wheel (bottom left side). Remove the fuse box cover lid and then flip the plastic fuse box cover over and you will find a small diagram showing where this fuse is located. Replace this fuse with a new one of the same number amp. Last thing to do is remove the cluster from your dash and check each light bulb and replace the bulb that is burned out. Sometimes when one bulb burns out, all of the lights won't work on the display. If that does not get it working again then you will need to remove the instrument cluster and just simply replace it for another used one found in your local junkyard. The instrument cluster is removed by prying off the plastic or simulated wood bezel that surrounds the drivers side dash and then removing four to six phillips screws with a phillips screwdriver. After you remove these screws, pull the cluster out and then disconnect the electrical plugs at the rear of your unit by pressing the clips together and then pulling away (at the same time)

Feb 04, 2011 | 2006 Ford Explorer

3 Answers

Replacment of a dash light. Toyota Corolla 1998


There is a plastic garnish surrounding the instrument cluster held in by 2 philips head screws. remove the screws and gently pry the garnish from top first then sides then it should pull out.

Then remove the 3 screws holding the cluster in place (2 bottom 1 top). Once that is done gently flip the cluster bottom up and pull out some to expose the wiring harness. Remove the 3 connectors from the back and then the cluster will pull out.

There are 3 bulbs that control the overall lighting of the cluster. They are spaced about every third across the rear of the cluster. They are the larger Green knobs. Remove the 3 large green knobs and replace the bulbs with the appropriate size. You can call your local parts store to find out the size.

Its a 5 minute job and does not require the entire removal of the dash board.

-ASE Master Tech
-Lexus Senior Tech
99 Corolla Owner.

Mar 13, 2009 | 1999 Toyota Corolla

2 Answers

How do i remove rear light cover to change stop light 1995 vw gol


OPEN REAR HATCH & TAKE TRIM OFF LEFT OR RIGHT SIDE & TWIST BULB HOLDER OUT OF BACK OF LIGHT

Feb 10, 2009 | 1995 Volkswagen Golf

1 Answer

Light is out in the dashboard


Remove the screws at the top of the black fascia that is in front of the clear plastic cluster lens

Pull the fascia off

Remove the 4 screws from each corner of the instrument cluster

Pull the cluster out, unplug all of the wire connectors

Do not disassemble the cluster; no need.

The bulbs are accessible at the rear of the cluster; twist to remove the bulb holders

Reassembly is easy, the connectors only fit one way.

Hope this helps.
Thnaks for choosing FixYa

Nov 05, 2008 | 2000 Toyota Tacoma PreRunner

Not finding what you are looking for?
2006 Hyundai Tiburon 2.0 Logo

Related Topics:

1,749 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...