Question about Cars & Trucks

Open Question

What is tappet clearance of 1997 maruti suzuki omni

My car is giving low mileage i also set the ignition timing & valve timing but didn't work plz help me

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Preeth Tom
  • 129 Answers

SOURCE: maruti zen engine stops working when running on slow speed.

hi
the problem may be due to the clutch plate and when your in low speed , increase the rpm ,what i mean is to raise the engine so that the engine will not stop

Posted on Jul 15, 2009

  • 156 Answers

SOURCE: valve tappet clearance of toyota 7k engine

7k clearances are ( HOT ) Inlet 0.008 in ( 0.20 mm )
Exhaust 0.012 in ( 0.30mm)

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Maruti esteem


check your ignition system and coolant temp sensor

Oct 14, 2013 | Cars & Trucks

1 Answer

Where is the fuse box of the maruti omnie


On this website (link below) you finde fuse box diagram and description, location too.

http://www.autogenius.info/en/maruti-suzuki-omni-fuse-box-diagram

May 13, 2013 | Cars & Trucks

1 Answer

I have Jaguar 2000 S type V6 engine 3 litre. I need to know valve clearances and how to adjust. This is the last avenue to take in relation to a sputtering engine miss at idle. I have replaced the...


Low mileage on the Jag to be having this problem. Usually the misfire on these engines is a weak coil, and they won't set a code. The 3.0 is derived from a Ford design and it uses direct-acting mechanical bucket tappets (DAMB) for the engine they put in the S type from 2000-05.
The adjustments are done with shims. I don't have access to the mfrs. specs on this computer..It is at my shop... If the tappets are not overly noisy you should not need an adjustment, or an adjustment that would keep the valves from sealing and opening.
I suggest running a compression test and a cylinder bleed down test on the wet cylinder. This information will be helpful in further troubleshooting and would eliminate a couple of possibilites.

I hope this helps & good luck with the Jag.

Aug 30, 2011 | Jaguar S-Type Cars & Trucks

1 Answer

Carburator and valve clearances


For the carb :
Idle r/min.- 1550+_50 r/min.
fuel level- 4.5+_5.0 mm
float height- 25.8+_1.0mm
pilot screw- 1-3/4 turns out
do you need jet #'s or not?

the "+_" signs are those plus-over-minus signs i cant do on my comp.

Valves:
valve diameter- in-30mm
ex-26mm

valve lift- in-5.5mm
ex-5.5mm

valve clearance or tappet clearance (cold):
in & ex: .08-.13mm

valve guide to valve stem clearance:
in-.010-.037mm
ex-.03-.057mm

valve guide I.D.: in & ex-5.5-5.512mm

valve stem O.D.:in-5.475-5.490mm
ex-5.455-5.470mm


Hope this helps.

Jan 30, 2011 | Suzuki Swift Cars & Trucks

1 Answer

Maruti omni 92 model show electrical circuit diagram


I need maruti omni van 1996 model, electrical wiring diagram & arrangement of head lights please post me

Aug 11, 2010 | Suzuki Esteem Cars & Trucks

4 Answers

Maruti zen engine stops working when running on slow speed.


you may try replacing the clutch lining, it may be too thin. hope this helps

Jul 15, 2009 | 1996 Suzuki Esteem

1 Answer

Valve tappet adjustment


well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Nov 18, 2008 | 1986 Suzuki Samurai

2 Answers

Valve clearances


On the intake 0.0008 or 0.0020 (it's in between these 2)

this is for the stem to guide clearance. (for the intake)

The Exhaust 0.0018 to 0.0030 stem to guide clearance.

Jul 10, 2008 | 1993 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...