Question about 1996 Chrysler Town & Country

1 Answer

Do you need a tool to take the locking ring off the fuel pump? and where can i get 1 at? i am trying to replace the fuel pump that is in the tank and can not get kit off. havea 1996

Posted by on

  • louise case
    louise case Jan 04, 2009

    will try this if i can get to it. thanks also my trans missiom is leaking mech says that 96 has problems with pan gasket leaking? this true?

  • louise case
    louise case Jan 04, 2009

    will try this if i can get to it. thanks also my trans missiom is leaking mech says that 96 has problems with pan gasket leaking? this true?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Screw drive on ring and tap with a hammer

Posted on Jan 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can't get fuel pump retaining ring off.


Hi Chuck,here's a guide to fuel pump removal,on yours it says you need a special wrench,ask Autozone for a loaner tool.

Jan 30, 2013 | 2001 Chevrolet Tahoe

1 Answer

I have a 1997 chevy tahoe 4x4 how do i change the fuel pump?


  • Disconnect the cable to the battery's negative terminal with a socket wrench. Loosen the filler cap on the fuel tank to relieve the pressure in the fuel tank. Drain the fuel tank by siphoning the fuel into a gasoline container with a hose. Raise the rear of the vehicle with a jack and support it on jack stands. Release the clamps on the hoses for the filler neck and vent tube of the fuel tank. Support the fuel tank with jack stands and detach the support straps for the fuel tank. Lower the fuel tank slightly and disconnect the electrical connections and hose on the fuel tank. Remove the fuel tank from the vehicle.

  • Turn the retaining ring on the fuel sender assembly counterclockwise with tool . Remove the retaining ring. Lift the fuel sender assembly out of the fuel tank and pull the fuel pump into the attaching hose while holding the bottom support of the fuel pump in place. Discard the O-ring on the fuel tank.
  • Install the new fuel pump into the attaching hose of the fuel sender assembly. Use care to avoid bending the fuel strainer since this will restrict fuel flow. Place a new O-ring on the fuel tank and install the fuel sender assembly into the fuel tank.

  • Place the locking ring on the fuel sender assembly and turn it clockwise with tool until the ring locks into place.

  • Install the fuel tank by reversing step 1. Pressurize the fuel system by turning the ignition on for two seconds and turning it off for 10 seconds. Turn the ignition on and check the fuel lines for leaks.
  • Jul 17, 2012 | Cars & Trucks

    2 Answers

    I need change the fuel pump


    Hi, The fuel pump is in the tank. You will have to remove the tank to get at it. Good luck

    Jun 21, 2011 | 1995 Ford Windstar

    1 Answer

    How do you change the fuel pump?


    Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Disconnect the negative battery cable.
    3. Relieve the fuel pressure.
    4. Remove or disconnect the following:
      • Rear seat cushion
      • Plastic access panel
      • Fuel pump wiring harness connector
      • Fuel lines
        7922jg34.gif

        View of fuel pump fittings through the floor pan
        Click to Enlarge 7922jg35.gif

        Remove the locking ring from the fuel pump sender with special tool Fuel Tank Sender Wrench D84P-9275-A
        Click to Enlarge

      • Fuel pump module lock ring. Use special tool Fuel Tank Sender Wrench D84P-9275-A.
      • Fuel pump module

    To install:

    1. Install or connect the following:
      • Fuel pump module with a new O-ring seal
      • Fuel pump module lock ring using special tool Fuel Tank Sender Wrench D84P-9275-A
      • Fuel lines
      • Fuel pump wiring harness connector
      • Plastic access panel
      • Rear seat cushion
      • Negative battery cable
    2. Start the engine and check for leaks and proper operation.
    shinehutt_37.gif

    hope this helps plz vote comment reply if need more help

    Jan 17, 2011 | 2002 Mercury Cougar

    1 Answer

    Whare is the fuel filter on 05 chev uplander


    Fuel Tank Module holds the fuel filter: Removal & Installation Short Wheel Base To Remove:
    Fuel tank (short wheelbase) gm-04-00-3125.gif

    1. Remove the Fuel tank.
    2. Disconnect the harness connectors from the module.
    3. Disconnect the fuel and emission hoses from the module. NOTE: To avoid damaging the lock ring, it is recommended to use special tool GM # J-45722 or equivalent to remove the lock ring.
    4. Using a spanner tool remove the fuel pump module lock ring. Fuel pump module gm-05-00-2551.gif

    5. Remove the fuel pump module and discard the O-ring seal. WARNING
      Drain the fuel from the fuel pump module into a fuel container to avoid the risk of fire and personal injury. Do not store fuel in an open container.
      NOTE: The lock ring may be reused even if "DO NOT REUSE" is stamped on it if the lock ring is not warped or damaged.
    6. Check the lock ring clearance on a flat surface using a feeler blade. If the lock ring is warped more than 0.016 in (0.41 mm), replace it.
    To Install:
    WARNING
    Replace the fuel module O-ring when reinstalling the fuel module to reduce the risk of a fuel leak that may cause a fire and personal injury.
    1. Install a new O-ring on the fuel tank.
    2. Place the fuel module into the fuel tank.
    3. Install the fuel module lock ring using a spanner tool.
    4. Connect the fuel and vapor hoses to the module.
    5. Connect the harness electrical connectors to the module.
    6. Install the Fuel Tank.
    7. Check for fuel leaks using the following procedure:
      • Step 1: Place the ignition in the ON position for 2 seconds
      • Step 2: Place the ignition in the OFF position for 10 seconds
      • Step 3: Place the ignition in the ON position
      • Step 4: Check for fuel leaks.
    Long Wheel base To Remove:
    Fuel tank (long wheelbase) gm-04-00-3113.gif

    1. Remove the Fuel Tank.
    2. Disconnect the harness connectors from the module.
    3. Disconnect the fuel and emission hoses from the module. NOTE: To avoid damaging the lock ring, it is recommended to use special tool GM # J-45722 or equivalent to remove the lock ring.
    4. Using a spanner tool remove the fuel pump module lock ring. Fuel pump module gm-05-00-2551.gif

    5. Remove the fuel pump module and discard the O-ring seal. WARNING
      Drain the fuel from the fuel pump module into a fuel container to avoid the risk of fire and personal injury. Do not store fuel in an open container.
      NOTE: The lock ring may be reused even if "DO NOT REUSE" is stamped on it if the lock ring is not warped or damaged.
    6. Check the lock ring clearance on a flat surface using a feeler blade. If the lock ring is warped more than 0.016 in (0.41 mm), replace it.
    To Install:
    WARNING
    Replace the fuel module O-ring when reinstalling the fuel module to reduce the risk of a fuel leak that may cause a fire and personal injury.
    1. Install a new O-ring on the fuel tank.
    2. Place the fuel module into the fuel tank.
    3. Install the fuel module lock ring using a spanner tool.
    4. Connect the fuel and vapor hoses to the module.
    5. Connect the harness electrical connectors to the module.
    6. Install the Fuel tank.
    7. Check for fuel leaks using the following procedure:
      • Step 1: Place the ignition in the ON position for 2 seconds
      • Step 2: Place the ignition in the OFF position for 10 seconds
      • Step 3: Place the ignition in the ON position
      • Step 4: Check for fuel leaks.
    prev.gif next.gif

    Oct 11, 2010 | 2005 Chevrolet Uplander

    1 Answer

    How to replace ford explorer fuel pump 1994


    REMOVAL & INSTALLATION NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
    1. Depressurize the fuel system and remove the fuel tank from the vehicle.
    2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
    3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
    4. Remove the fuel pump and bracket assembly.
    5. Remove the seal gasket and discard it. To install:
    6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up 89685g02.gif
      Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up 89685g03.gif
      Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer 89685g04.gif

    7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
    8. Install the tank in the vehicle.
    9. Install a minimum of 10 gallons of fuel and check for leaks.
    10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
    11. Remove the pressure gauge. Start the engine and check for fuel leaks.
    prev.gif next.gif

    Jul 31, 2010 | 1994 Ford Explorer Limited

    1 Answer

    Is there an easier way to replace the fuel pump other than dropping the tank?


    No, the fuel tank must be dropped if there is no access door (which there usually isn't for safety reasons).


    REMOVAL & INSTALLATION NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
    1. Depressurize the fuel system and remove the fuel tank from the vehicle.
    2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
    3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
    4. Remove the fuel pump and bracket assembly.
    5. Remove the seal gasket and discard it. To install:
    6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up 89685g02.gif
      Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up 89685g03.gif
      Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer 89685g04.gif

    7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
    8. Install the tank in the vehicle.
    9. Install a minimum of 10 gallons of fuel and check for leaks.
    10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
    11. Remove the pressure gauge. Start the engine and check for fuel leaks.
    prev.gif next.gif

    Jul 26, 2010 | 1998 Ford Explorer

    1 Answer

    NEED TO REPLACE FUEL PUMP FOR 1996 fORD eXPLORER, V6 4.0. WHERE IS IT AND HOW DO I GET TO IT?


    Great SUV, I have the same model; for Ford Ranger/Explorer/Mountaineer 1991-1999 check this procedure to Fuel Pump - REMOVAL & INSTALLATION...
    (see Figures 1, 2 and 3)

    To gain access to the fuel pump, it is necessary to remove the fuel tank.
    1. Depressurize the fuel system and remove the fuel tank from the vehicle.
    2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
    3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
    4. Remove the fuel pump and bracket assembly.
    5. Remove the seal gasket and discard it.
    To install:
    1. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
    ab80e6f.jpg

    Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up

    fe10412.jpg

    Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up

    2bf46c6.jpg

    Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer
    1. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
    2. Install the tank in the vehicle.
    3. Install a minimum of 10 gallons of fuel and check for leaks.
    4. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
    5. Remove the pressure gauge. Start the engine and check for fuel leaks.

    Hope help with this; remember comment and rated this help. TY for using Fixya.

    May 28, 2010 | 1996 Ford Explorer

    2 Answers

    How to replace my 2001 ford taurus fuel pump Instructions


    2001 Ford Taurus V6-3.0L DOHC VIN S
    Fuel Pump: Service and Repair

    REMOVAL
    1. Remove the fuel tank.
    2. Clean the area around the fuel pump mounting flange.
    3. Using the special tool, remove the fuel module retaining ring.(Screwdriver and hammer)
    4. Remove the fuel delivery module from the fuel tank.
    CAUTION: The fuel delivery module must be handled carefully to avoid damage to the float arm, filter, and convolute hoses.
    INSTALLATION
    1. To install, reverse the removal procedure.
    NOTE: A stop should be felt when aligning the raised arrow on top of the fuel tank delivery module to the dot on the fuel tank.

    Sep 08, 2009 | 2001 Ford Taurus

    2 Answers

    How do I remove the fuel Tank on a 1996 ford ranger?


    You need to seperate the tank and pump for tank to be able to be seperated from vechical or you can attempt to remove the fuel lines. and all you need to do is release the tank straps with a 9/16 socket and be sure it is supported and low in gas. To gain access to the fuel pump, it is necessary to remove the fuel tank.
    1. Depressurize the fuel system and remove the fuel tank from the vehicle.
    2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
    3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
    4. Remove the fuel pump and bracket assembly.
    5. Remove the seal gasket and discard it.

    To install:
    1. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.



    0900c1528018ee69.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up

    Jul 10, 2009 | 1996 Ford Ranger SuperCab

    Not finding what you are looking for?
    1996 Chrysler Town & Country Logo

    Related Topics:

    65 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    63801 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    chargerhp
    chargerhp

    Level 3 Expert

    813 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...