Question about Cars & Trucks

Open Question

Have a p1610 code on a 2002 nissan altima what is the problem

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 54 Answers

SOURCE: Tune up nissan altima 2.5L model 2002

All you really need is a good set of spark plugs, this car has coil packs so no plug wires distributor caps etc.....Just remove the coil packs and install your plugs and your done. Good luck.

Posted on May 31, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

  • 733 Answers

SOURCE: what is an code po300 and po420 and what do i need

The p0300 code is a random missfire code sometimes caused by bad spark plugs and wires, if you have not done a tune up, it's time for one. now, the p0420 code is for catalyst efficiency below threshold, basically, your catalytic converter is bad and may need to be replaced. Sometimes repairing the random missfire can eventually clear the p0420 code. your car is not burning fuel properly, therefore the catalytic converter is getting dirty. Also, if you notice blue smoke coming out the tail pipe, then that's the cause for a failing catalytic converter as oil is getting to the combustion chamber and being burned off through the exhaust.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code p1610 mean


A P1610 Code has to do with the NATS system which is the security system in your car. If you look at your key there is a small blue square in it which contains a chip. This chip sends a signal to your immobilizer in your steering column and then to the Electric Control Module. If the ECM does not recognize the ID of the key then it will prevent it from starting.
Try resetting the ECM to get it to start and take it to the dealer. With luck all they have to do is re-program the keys to your ECM again. Worst case scenario, your ECM is toasted and you will need to get a new one. Good Luck!

Oct 16, 2014 | 2002 Nissan Altima

2 Answers

My 2006 nissan altima 2.5 S wont start.


You really need the dealer on this one.

Jul 17, 2012 | 2006 Nissan Altima 2.5

1 Answer

P1610 and P1614 Keys won't turn for Lock Position on Ignition Lock Cylinder


Not sure what the problem here is.
The codes are for the security system - - the key is not sending a signal or the right signal for the car to start.
Could be a problem with the lock cylinder which may have a sensor for the key inside it.

Jul 02, 2012 | 2002 Nissan Altima

1 Answer

Got NATS code P1610 car wont start but it is turning! please help


difference of key or unregistered key used.send it to nissan to have key registered or call alock smith that has the right equipment.it sucks i know!

Jun 27, 2011 | 2001 Nissan Altima

2 Answers

2003 Nisson Altima code P1610 and P1612. Anti theft problem how do I reset without taking to Nisson dealer?


P1610=Lock Mode--1 turn ignition switch OFF 2 turn ignition switch ON with registered key. (Do not start engine.) Wait 5 seconds. 3 Return the key to off position. 4 Repeat steps 2 and 3 twice ( total of tree cycles). 5 Start the engine. Does engine start ?? Yes...System is OK. Now system is escaped from LOCK MODE...if no start...Go to 3
P1612 is a lot of testing.......get back to me....

Jun 04, 2011 | Nissan Altima Cars & Trucks

2 Answers

My nissan try to cranck up but it wont start code p1610 and p1612 came out


my nissan altima 2002 wont start the battery is brand new and code P-1612 was found out what does the code mean

May 05, 2011 | Nissan Pathfinder Cars & Trucks

3 Answers

Code p1610,p1612


Sentra 2003 p1612 code

Sep 06, 2010 | 2002 Nissan Altima

1 Answer

2002 Nissan Altima P0720, P1574, P0420


I have a 2002 Nissan Altima. Can anyone tell me what these codes are? And how to fix them? P0420

Apr 02, 2010 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...