Question about 2006 Nissan Altima

1 Answer

Keyless entry remote

How do I program an keyless entry remote for a 2006 Nissan Altima?

Posted by on

  • kirk_dudley Jan 07, 2009

    IT WORKED FOR ONE REMOTE BUT NOT THE OTHER. I DON'T KNOW WHY. THANKS FOR YOUR HELP.

  • Anonymous Mar 13, 2014

    2006 chysler pacifica keyless remote

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Hello Kirk , follow these instructions carefully :

sitting in car with all the remotes you wish to register with the vehicle readily available ,,close all doors ! insert key into ignition and remove 6 times within 10 seconds ,, (hazzard warning lamps will then flash twice) ** note withdraw key completely from the cylinder each time ,, if procedure is done too fast it will not enter registration mode ,, ok ,, insert ignition key into cylinder and turn to the accessory position ,, Push any button on the key fob once ,, (hazzard warning lamps will then flash twice),, at this time the new ID code is entered ,, at this time open drivers door ,, check operation of all remotes ..

enjoy Mate .

Posted on Jan 04, 2009

  • Rick Byrd
    Rick Byrd Jan 07, 2009

    for multiple remotes programming :
    follow steps from above , but do not open the door to end the programming mode , NOW , additional programming steps , unlock the door and lock it again with the lock/unlock switch on the drivers door , push any button on the next key fob you wish to register , (hazzard warning lamps will then flash twice),, at this time the new ID
    code is entered for 2nd remote , (up to 5 remotes can be registered) if you wish to program another remote repeat these steps , if you are done programming remotes at this time open drivers door ,, check operation of all remotes ..thanks kirk , i could use a fix ya .

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lastyear i wreck my 2005 nissan altima, i still have the keyless remote part but not the ignition key, now i have a 2004 nissan altima but no remote are they compatible


Call Nissan they have to program your old keyless remote to your new cars ECU. Unless your a computer wiz you can do so research and get the program to do it yourself. Call Nissan first.

Mar 07, 2016 | Nissan Cars & Trucks

3 Answers

Keyless entry remote no longer works and alarm led light located between the front seats is no longer on or can be alarmed.


I had to huy a new fob key for my car. If i didnt i cudnt even start my car. If for a dodge charger. Actually selling it. Person wud just have to reprogram it to there car... so u will probably have to get new keyless remote and have programmed to your car.. mine was almost 400. Dollars

Jul 29, 2015 | 1995 Nissan Altima

1 Answer

Where can i find the relay or fuse of the remote keyless entry in my 2006 nissan sentra?


http://www.b15u.com/threads/36-Relay-amp-Fuse-Diagrams

The room lamp check fuse then the relay for keyless in passenger fuse panel

May 16, 2015 | 2006 Nissan Sentra

1 Answer

How do I program my Nissan Altima 2006 keyless remote


Hi. It's most likely a problem with the remote. Programing can only be done at the dealership

Feb 20, 2014 | Nissan Cars & Trucks

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

2 Answers

Hi. Do you what the FCC ID is for the Nissan Versa (Tiida) 2006. I am trying to purchase a new keyless remote. Thanks. RJ


I believe that with most keyless entry systems, you must buy the remote specific to Nissan Versas, and then either take it to a dealer to have them program your in-car receiver to understand the new remote signal, or download the instructions and add it yourself. FCC ID should have absolutely bearing on this.


Dec 04, 2009 | 2006 Nissan Versa

Not finding what you are looking for?
2006 Nissan Altima Logo

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...