Question about Volkswagen Polo

1 Answer

Polo 1.6 has been overhauled,problm is is engines runs 4 some minutes en stops,as if it has an aiflow problem,en im nt wheather a ring at the crank shaft at back if it is inserted correctlz

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

It sounds like there is a problem on the fuel system. connect a fuel pressure gauge to check pressure. it should be at least 3bar. if not check fuelfilter 1st then fuel pump.

Posted on Nov 04, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

3dmaster
  • 183 Answers

SOURCE: 2001 vw polo

Dear Customer,

1
check your sensors 1st,all sensors must be good

2
if all sensors are working good than check your engine firing sequence,some times happens when sequence was wrong,

3
check your exhaust and carborator tuning pin that creates the batter combination for firing in bore for batter performance & less emitions ,so check is it ok or not than go to your nearest service center that havad certified mechanics,

till you read this you had solve this problem definatly,

THNX

Posted on May 18, 2008

SOURCE: 1999 cavalier misfire/crank shaft code

sounds like you could of crosed your wires

Posted on Oct 20, 2008

  • 3 Answers

SOURCE: Is it hard to change crank shaft position on hyundai santa fe 01

2.7 engine located above the starter. You need to remove the starter outherwise its fairly easy.
The 2.4 & 3.5 engine, its located in the front next to the timing belt, a little more complicated to to install.

Posted on Aug 18, 2009

  • 1 Answer

SOURCE: newly overhauled toyota corolla 2e engine emits black smoke

I have toyota corona 3s engine it smokes black and fuel consuption is high we have changed the engine oil and cylinderhead gassecate but still black smoke is comming what should i do

Posted on Mar 29, 2010

typo_86
  • 5 Answers

SOURCE: im a having a misfire

well i hate to say it but you need to replace the piston rings to fix that problem

Posted on Oct 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Newly overhaul isuzu 4ja1 but oil comes out from positive crankcase ventilation


im having the same experience with my isuzu rodeo 1990 4ja1. i overhauled it last december, spent almost 1500dollars on the overhaul kit and again 300 for paying the guy. The engine was running very good and brand new for 2 days only when i suddenly noticed a big drop in engine power while driving. There's oil coming out of the head breather tube and pushing it into the intake manifold. And now much worse oil coming out of my dipstick and my front and rear crank seal also. Can someone please tell me what the problem and best solution is because my car has not even driven for a year with the new overhaul kit and im having the same problems again. This issue is really driving me crazy.

Sep 29, 2013 | Cars & Trucks

1 Answer

My 1992 mustang lx hatcback 2.3L non turbo hesitates and chugs when I press on the accelerator?


This is a sign the engine is burning oil. The oil id getting into the combustion chamber either by the waorn valve guides or via worn piston rings.
A compression test can determine if you have worn piston rings.
If you have worn piston rings then this is a major engine overhaul.
Worn valve guides is a minor engine overhaul.

Dec 12, 2012 | 1992 Ford Mustang

1 Answer

Hi.my 1999 vw polo classic 1.4i is blowing oil with pressure from the o-ring on the oil filter. just finished overhauling the engine. didnt replace the oil pump though.have resorted to replacing the entire...


First check and see if the seal on the filter lines up right. Use your filter wrench to snug the filter a little extra. Try to put a manuel oil presure gauge on it. If this fails Im assuming having just rebuilt the engine you have a manuel. Check it out and find out where your oil pressure regulator is. Its probably sticking.

Jul 08, 2011 | Volkswagen Polo Cars & Trucks

2 Answers

Vw polo 1 litre has idling problems it keeps reving to around 800 rpm then droping to around 400/500 all the time engine being cold or warm makes no difference. It's a w reg with 50000 miles


im also havin a problm with 99 polo 1.6 it revs high low high low and if da tank is below 1/4 it dies of while driving iv changed tank unit,trottle body, sensor nd after i changd tank unit da foat reads opsite way sum1 plz help me

May 20, 2010 | Cars & Trucks

1 Answer

Excessive smoke in the tail pipe


1988, time to send it to the wrecker... or put in a crate motor.

how much oil is it burning between oil changes?

only a few ways oil gets burnt in the exhaust.

1) worn out rings - overhaul (running thick oil might help a little)
2) worn out valve guides - overhaul (running thick oil might help a little)
3) blow by is forcing it into the PCV system - overhaul
4) crack somewhere between the oil gallery and the intake... this usally run really bad though...


yep kinda sums it up.... overhaul (replace or wrecker)

Peace

Feb 27, 2010 | 1988 Toyota Corolla 4 Door

1 Answer

Hollow bolt torque and oil presser warning light


torque it to 65% of the maximum torque rating for that diameter bolt

Jun 25, 2009 | 1998 Subaru Legacy

3 Answers

Newly overhauled toyota corolla 2e engine emits black smoke


I have toyota corona 3s engine it smokes black and fuel consuption is high we have changed the engine oil and cylinderhead gassecate but still black smoke is comming what should i do

Jan 21, 2009 | 1989 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...