Question about 2007 Dodge Caliber SXT Sport Hatchback

Open Question

Brake lights on 2007 dodge caliber

Top brake light works side ones do not does not appear to be bulbs or fuse

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: tail light works but no brake light on2003 Dodge Ram 1500

if it has a trailer package look at the splitter when you take off the tail light cover might be that plug.

Posted on Dec 23, 2008


SOURCE: 2007 Dodge Caliber backup lights not working

Check the fuse for the back-up lights. Also, check the bulbs themselves.

Posted on Mar 23, 2009

  • 1392 Answers

SOURCE: 2004 dodge durango left rear taillight won't light

Check for a bad socket assembly. Look for burnt retainers inside the socket.

Posted on Jul 29, 2009

  • 986 Answers

SOURCE: how to change head light bulbs on a dodge caliber

Park the Dodge Caliber on a flat paved or concrete surface. Turn the steering wheel all the way to the side opposite the headlight you are replacing. In other words, if you are replacing the left headlight, turn the wheel all the way to the right. Apply the parking brake and release the hood latch.

  • Step 2 Place a wheel chock behind one of the rear tires.
  • Step 3 Open the hood. This is to allow some light to reach down into the engine compartment.
  • Step 4 Raise the front quarter panel of the side you need to replace the headlight on with the floor jack and place the jack stand under the front frame rail on that side.
  • Step 5 Remove the fender well plugs using the plastic plug puller tool. You do not have to remove the entire fender well cover, but the more plugs you remove, the more access it will give you to the headlight assembly.
  • Step 6 Unplug the headlight switch. Make sure you are unplugging the headlight which will be the inboard plug.
  • Step 7 Turn the headlight bezel a quarter turn counterclockwise and extract the bulb and bezel.
  • Step 8 Insert the new headlight into the bezel, being careful not to touch the glass bulb.
  • Step 9 Insert the bezel and headlight into the headlight assembly and turn a quarter turn clockwise to lock it into place.
  • Step 10 Plug the wire connector into the headlight. This would be a good time to get up and go test the light to make sure it's working.
  • Step 11
  • Posted on Dec 28, 2009

    • 10865 Answers

    SOURCE: 2007 Dodge Caliber R/T dashboard lighting

    It may be lose or burned out. Call the local auto-electric shops and ask what they would charge you to replace it

    Posted on Mar 02, 2010

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    No brake lights and Gearshift won't come out of park

    That sounds like a defective brake light switch, located
    by the brake pedal. If you normally would have to depress the
    brake pedal to shift out of park, the problem lies in the vicinity
    of the brake light/pedal switch.

    Aug 20, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

    1 Answer

    My driver side headlamp won't work even with new bulb

    check for a fuse probably your car have separated fuses for every light side.

    Aug 27, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

    1 Answer

    Dodge 2007 Caliber SXT headlight relay

    A relay problem would disable both the lights not just one.

    Jun 06, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

    2 Answers

    2007 dodge caliber brake lights dont work, bulbs are good, hatch back brake light works any ideas what this could be. derek

    Check the connections on the "body harness" that is located near the hinge for the decklid.this harness,if i remember correctly,is on the driver-side of the car.Also check to make that no wire has any "bare spots"that are grounding to any metal.

    Feb 12, 2011 | Dodge Caliber Cars & Trucks

    1 Answer

    2007 dodge caliber transmission light is on

    You'll notice what appears to be a dipstick tube at the front of the vehicle on the drivers side, and it should have a warning label to use CVT oil. But when you remove the top, there's no stick. The dipstick itself is a "special tool" (Miller No. 9336). The stick is marked for fluid levels for different temperatures, although there is an acceptable range.
    Read the instructions carefuly that come with the tool
    Thank you!

    Jul 12, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

    2 Answers

    Will not go to drive and no brake lights work

    the problem is the brake lights, repair them and it will come out of park

    Oct 05, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

    2 Answers

    My break lights won't work. thought it was a fuse

    look up above your brake pedal and you should see a switch that should look like a rectangle. Odds are this switch is broken and it is what tells your brake lights to come on when it depresses.

    Sep 04, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

    2 Answers

    How do you replace break lights in 2007 Dodge Caliber?

    Look inside the rear hatch area near the very rear of the vehicle. You should find a removable panel near the brake light housing. After you carefully remove the panel, look for some plastic wingnuts that hold the light housing in, and remove them, you should not need any tools to do this. After the nuts are removed you should be able to gently remove the tail light assembly from the rear of the car. Becareful not to damage the wiring. Now look at the back side of the tail lamp assembly and look for a locking tab on the light socket. Depress the locking tab and twist the light socket about a quarter turn, then pull the light socket away from the light housing. Pull the bulb out and replace it. Then reassemble and your done.

    Aug 27, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

    1 Answer

    2007 Dodge Caliber backup lights not working

    Check the fuse for the back-up lights. Also, check the bulbs themselves.

    Mar 22, 2009 | 2007 Dodge Caliber SRT4 Hatchback

    Not finding what you are looking for?
    2007 Dodge Caliber SXT Sport Hatchback Logo

    Related Topics:

    93 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts


    Level 3 Expert

    78919 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides