Question about Cars & Trucks

Open Question

How to remove the lower ball joint on a 2007 kia sedona

How to remove the mounting studs

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: lower ball joint removal how to

  1. Remove the steering knuckle with wheel hub and bearing attached.
  2. Remove the lower ball joint flange with a chisel.
  3. Install J9519-E and J34874 to the lower ball joint.
  4. Remove the lower ball joint from the lower control arm using J9519-E and J34874


  1. Install the lower ball joint and J9519-E, J41435, and J45105-2 to the lower control arm.
  2. Install the lower ball joint to the lower control arm using J9519-E, J41435, and J45105-2.
  3. Remove J9519-E, J41435, and J45105-2 from the lower control arm
    1. Install J9519-E and J45105-1 to the lower ball joint.
    2. Flare the lower ball joint flange using J9519-E and J45105-1.
    3. Remove J9519-E and J45105-1 from the lower ball joint.
    4. Install the steering knuckle with wheel hub and bearing attached. Install the tire and wheel.
    1. Lower the vehicle.
    2. Check the front wheel alignment.
these jouints are pressed in and there is a flange that is flared this is what the tool numbers refer too.

Posted on Sep 12, 2008

Ad
chrischronic
  • 235 Answers

SOURCE: lower ball joint broke on a 95' lincoln towncar

it must be pressed out with a ball joint press then new one pressed back in. this job is for a machanic

Posted on Apr 15, 2009

  • 19 Answers

SOURCE: removal and replacement of a

You will need certain tools to remove the ball joint. You will need a ball joint removal and installation kit you can find at a local automotive store.Remove brakes and control arms to easily get to ball joint and start the removal. The ball joint kit has instructions on how to remove and install your new ball joint.

Posted on Jul 27, 2009

emissionwiz
  • 76846 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

  • 603 Answers

SOURCE: I need instructions for lower ball joint removal

If your replacing ball joint anyway try this -
loosen nut the the point where it is just past the end of the bolt, then hit the nut to make everything come apart. The ball joint will be damaged, but if your replacing it anyway.....

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Latitude. How can I replace control arm and ball joint assembly?


Lower you can do fairly easy. Upper, a bit tougher.For the upper you will need a spring compressor.

Mar 21, 2016 | 2011 Jeep Patriot

1 Answer

Im having a problem getting the lower ball joint off my 2004 kia sedona i have everything offf exept 3 bolts that wont budge


Penetrating oil is your beat bet. Use something that isn't silicone or lithium based. If you don't have an impact don't be afraid to get rough with it. Worst case scenario you snap the bolt. If that happens grind it flush after you get the ball joint off, center punch the broken bolt drill it out to just under the thread size and get the threads out.

Mar 25, 2014 | 2004 Kia Sedona

1 Answer

I am trying to take the lower control arm on the passenger side of a 98 transport. The lower ball joint is being stubborn. I tried ball joint remover tool and not much room to work with and still dont


Lower Control Arm

Print
The lower control arm is a two-piece welded unit with a riveted ball joint. A conventional rubber bushing is used for the rear lower control arm pivot. The front lower control arm bushing is mounted vertically.


REMOVAL AND INSTALLATION

Some special tools are required to perform this operation including, a front hub spindle removal tool and a suitable ball joint separator tool.

WARNING Do not hammer or pry ball joint from knuckle. Failure to use recommended tools may cause damage to the ball joint and seal.
See Figure 1


0900c152801dbd3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Exploded view of the control arm-to-frame mounting

  1. Raise the vehicle and suitably support by the frame allowing the control arms to hang free.
  2. Remove the wheel and tire assembly.
  3. Remove the steering gear outer tie rod from the steering knuckle.
  4. Remove the stabilizer shaft link from the control arm.
  5. Remove the front drive axle shaft nut and washer.
  6. Use a suitable front hub spindle removal tool to Push the axle splines back out of the front wheel drive shaft bearing.
  7. Remove the drive axle from the transaxle.

Drive axle joint seal protectors should be used anytime service is performed on or near the drive axles. Failure to observe this could result in joint or seal failure.
  1. Place a modified inner drive joint seal protector on the drive axle joints.
  2. If equipped, remove the ABS wheel speed sensor jumper harness.
  3. Remove and discard the cotter pin, then loosen the nut from the ball stud.
  4. Remove the pinch bolt and the control arm mounting bolts, then remove the control arm from the vehicle.

Apr 20, 2013 | Pontiac Cars & Trucks

1 Answer

Control arm removal


Take the wheel off, secure strut to lower frame with a strong piece of rope, place a jack under the sway bar, jack up slightly, that will hold the strut from lowering anymore via the link from the sway arm to the strut (reason for the rope securing the strut is it will swing out towards you when the lower control arm is removed), saturate all the bolts with a good penatrating oil [Liquid Wrench = Good Stuff] remove the nut from the lower ball joint stud, spray on more penatrating oil where stud goes through spindle, hit the spindle with a good size hammer where the ball joint stud goes through the spindle (always hit what it goes through), give it several hard sharp raps from the sides, then hit downward on the lower control arm with hammer, most of the time the stud will come right out, if not, put nut back on ball joint stud just until the stud is flush with the top of the nut, since you can not hit directly on the top of stud, get a good sized wrench to go across the stud and hit downward on either side of the wrench, holding other end with your other hand, if the ball joint does not come out now, hit the spindle from the sides some more HARD, then hit downward on control arm, if it still does not come loose you will have to get (or rent) a spreader (Pickle Fork) to separate the ball joint from the spindle, then remove the two bolts from the lower frame, slide lower control arm out.

Sep 11, 2012 | 2000 Mercury Cougar

1 Answer

How to change rear ball joints on 2002 dodge stratus


Instructions
  1. Remove the Upper Control Arm
    • 1Disconnect the ground battery cable using a wrench.
    • Loosen the front wheel lugs located on the same side of the upper ball joint you need to replace. Use a lug wrench.
    • Raise that same front wheel off the ground using a floor jack and support the vehicle on a jack stand.
    • Finish removing the tire.
    • Take the cotter pin off the upper ball joint stud holding the steering knuckle arm. Use a pair of nose pliers.
    • Remove the castle nut from the upper ball joint stud using a wrench or ratchet, ratchet extension and deep socket.
    • Loosen the two bolts securing the back of the upper control arm to the mounting bracket. Use a wrench to hold the bolt head as you loosen the retaining nut with a ratchet and socket.
    • Pull the control-arm ball joint off the steering knuckle arm. You may need to use a Pitman arm puller to free the ball joint.
    • Finish removing the two bolts from the back of the upper control arm and lift the upper control arm off the vehicle.
    Install the New Upper Control Arm
    • Set the new upper control arm in place and install the two bolts and retaining nuts to secure the back of the upper control arm to the mounting bracket. Remember the bolt heads should point inward toward the shock absorber with the retaining nuts on the outside of the mounting bracket. Do not tighten the bolts yet.
    • 11Insert the control-arm ball joint on the steering knuckle arm and start the castle nut with your hand over the ball joint stud. Do not tighten the nut yet.
    • Tighten the two bolts on the mounting bracket to 67-foot lbs. (91 Nm) using a torque wrench. Hold the bolts with a backup wrench as you tighten the retaining nuts with the torque wrench.
    • Tighten the ball-joint castle nut to 45-foot lbs. (61 Nm) using the torque wrench, ratchet extension and deep socket.
    • Install a new cotter pin through the joint-ball stud hole using the nose pliers. If necessary, tighten the castle nut just a few degrees to clear the stud hole through one of the castle nut slots.
    • Mount the tire on the wheel assembly and install the wheel lugs using the lug wrench.
    • Lower the vehicle and finish tightening the wheel lugs.

May 31, 2012 | Dodge Stratus Cars & Trucks

1 Answer

How do i replce ball joints on a 99 pontiac sufire


Lower Control Arm Ball Joint Replacement Removal Procedure Tools Required J 43828 Ball Joint Separator
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Remove the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .
  4. Remove the wiring harness from the lower control arm.

  5. 165249.gif
    tif.gif
  6. Remove the cotter pin (1) from the ball joint (3).
  7. Remove the nut (4) from the ball joint (3).

  8. 490085.gif
    tif.gif
    Notice: Use only the recommended tools for separating the ball joint from the knuckle. Failure to use the recommended tools may cause damage to the ball joint and seal.
  9. Remove the ball joint from the steering knuckle using the J 43828 .

  10. 491742.gif
    tif.gif
  11. Remove the lower control arm front (1) and rear (4) mounting bolts.
  12. Remove the lower control arm (1) from the vehicle and place in a vice.
  13. Drill out the 3 rivets (3) retaining the ball joint to the lower control arm (2).
  14. Use a 3 mm (1/8 in) drill bit in order to make a pilot hole through the rivets.
    Finish drilling the rivets with a 13 mm (½ in) drill bit.
  15. Remove the ball joint (4) from the control arm (2).
Installation Procedure

    165250.gif
    tif.gif
  1. Install the ball joint (4) into the control arm (2).
  2. Install the 3 ball joint bolts (3) and the nuts (1). Follow the instructions in the ball joint kit. Tighten the ball joint bolts (3) according to the specifications in the instructions.

  3. 491742.gif
    tif.gif
  4. Install the lower control arm (2) to the front suspension support (1)
  5. Notice: Refer to Fastener Notice in the Preface section.
  6. Install the lower control arm front (5) and rear (4) mounting bolts.
  7. Tighten • Tighten the front bolt to 107 N·m (79 lb ft). • Tighten the rear bolt to 110 N·m (81 lb ft).
    165249.gif
    tif.gif
  8. Install the lower ball joint stud (3) to the steering knuckle (2).
  9. Install the ball joint stud (3) through the steering knuckle (2).
  10. Install the ball joint nut (4).
  11. Tighten
    Tighten the ball joint nut to 55 N·m (41 lb ft) plus 180 degree rotation minimum-65 N·m (50 lb ft) plus 180 degree rotation maximum to install the cotter pin.
  12. Install the wiring harness to the lower control arm.
  13. Install the cotter pin (1).
  14. Install the stabilizer link to the lower control arm. Refer to Stabilizer Shaft Link Replacement .
  15. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  16. Inspect the front wheel alignment. Refer to Wheel Alignment Specifications in Wheel Alignment.

Sep 15, 2011 | 2003 Pontiac Sunfire

1 Answer

How do you replace ball joints


Removing the Ball Joint Step 1 Loosen the lug nuts on the front wheel assembly with the ball joint you need to replace. Do not remove the lug nuts.
Step 2 Set the transmission in neutral (manual) or park (automatic) and raise the wheel off the ground using a floor jack. Then support the car on a jack stand.
Step 3 Chock the rear wheels and apply the parking brake.
Step 4 Remove the wheel lugs and the wheel assembly.
Step 5 Remove the mounting nut and dished washer that secure the stabilizer bar to the control arm. Use a wrench or ratchet and socket.
Step 6 Unscrew and remove the mounting bolt and nut holding the inner side of the control arm to the car's body. This will relieve the tension on the stabilizer bar. Use a wrench to hold the mounting bolt as you unscrew the nut with a wrench or ratchet and socket.
Step 7 Unscrew the bolt on the steering knuckle that holds the control-arm ball joint to the knuckle. Use a wrench or ratchet and socket.
Step 8 Spread the steering knuckle joint that holds the control-arm ball joint to the knuckle. Use a large screwdriver or pry bar. Then separate the ball joint from the steering knuckle.
Step 9 Pull the control arm from the stabilizer bar.
Step 10 Remove the stabilizer bar spacer from the control arm and keep it in a secure place. You will need to use it on the new control-arm ball joint assembly.
Installing the Ball Joint Step 1 Insert the new control-arm ball joint stud into the steering knuckle joint. As you look through the mounting bolt hole on the steering knuckle, align the notch on the ball joint stud with the hole. Insert a new ball joint mounting bolt and start a new nut on the bolt. Tighten the nut.
Step 2 Mount the stabilizer bar spacer in the control arm, then insert the stud bolt at the end of the stabilizer bar into the control arm mounting hole and spacer.
Step 3 Set the other end of the control arm in its mounting position and insert the mounting bolt. Then start the mounting nut on the bolt by hand.
Step 4 Hold the head of the mounting bolt that secures the control arm to the car's body using a wrench, then tighten the nut.
Step 5 Secure the stabilizer bar to the control arm with the dished washer and mounting nut. Tighten the nut.
Step 6 Install the wheel assembly and lugs. Tighten the lugs with the lug wrench just enough to hold the wheel assembly firmly in place.
Step 7 Lower the vehicle and finish tightening the wheel lugs.
Step 8
Remove the chocks from the rear wheels.

Aug 08, 2010 | 1998 Ford Escort

1 Answer

Remove front axle


pull lower ball joint on lower controle arm. remove axle nut. pull axle reverse to replace. not hard

Aug 06, 2010 | 2005 Kia Sedona

1 Answer

I need to replace my ball joints. can you give me some tips on how to do this? I have never done this before and i would appreciate some pointers on what i need to do to get the job done. Thank you very...


UPPER BALL JOINTS
  1. Raise and support the truck with jackstands. Remove wheel.
  2. Support the lower control arm with a floor jack.
  3. Remove the cotter pin from the upper ball stud and loosen, but do not remove the stud nut.
  4. Using a forcing-type ball joint separator tool, loosen the ball stud in the steering knuckle. When the stud is loose, remove the tool and the stud nut. It may be necessary to remove the brake caliper and wire it to the frame to gain clearance.
  5. On R-series trucks, drill out the rivets using a 1 / 8 in. drill bit. Remove the ball joint assembly.
  6. On C-series trucks, drill out the rivets using a 1 / 8 in. drill bit to start a pilot hole. Drill out the rivets with a 1 / 2 in. bit. Remove the ball joint assembly using a screw-type forcing tool.

To install:
Installation is the reverse of removal but please note the following important steps.
  1. On R-series vehicles, tighten the ball joint nuts to 18 ft. lbs. (24 Nm).
  2. On R-series vehicles, tighten the ball stud nut as follows:

    1 / 2 ton trucks: 50 ft. lbs. (68 Nm), plus the additional torque to align the cotter pin. Do not exceed 90 ft. lbs. (122 Nm) and never back the nut off to align the pin. 3 / 4 and 1 ton trucks: 90 ft. lbs. (122 Nm), plus additional torque necessary to align the cotter pin. Do not exceed 130 ft. lbs. (176 Nm) and never back off the nut to align the pin.
  3. On C-series vehicles, tighten the ball joint nuts as follows:

    1988-90 models, tighten the nuts to 17 ft. lbs. (23 Nm) for the 15 and 25 Series and 52 ft. lbs. (70 Nm) for 35 the Series. 1991-98 models, tighten the nuts to 18 ft. lbs. (24 Nm).
  4. On C-series vehicles, tighten the ball stud nut to 90 ft. lbs. (120 Nm) on 1988-90 models, 84 ft. lbs. (115 Nm) on 1991-95 models and 74 ft. lbs. (100 Nm) on 1996-98 models.
  5. Install a new lube fitting and lubricate the new joint.
LOWER BALL JOINTS
  1. Raise and support the front end on jackstands.
  2. Support the lower control arm with a floor jack.
  3. Remove the wheel.
  4. Remove the lower stud cotter pin and loosen, but do not remove, the stud nut.



0900c1528008f64b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Remove the lower ball joint using a suitable tool-R-Series shown, C-series similar


0900c1528008f64c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Use an appropriate tool to separate the lower ball joint from the steering knuckle-R and C-Series


0900c1528008f64d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Installing the lower ball joint-R and C-Series
  1. Loosen the ball joint with a forcing-type ball joint tool. It may be necessary to remove the brake caliper and wire it to the frame to gain enough clearance.
  2. When the stud is loose, remove the tool and ball stud nut.
  3. Install a spring compressor on the coil spring for safety.
  4. Pull the brake disc and knuckle assembly up and off the ball stud and support the upper arm with a block of wood.
  5. Remove the ball joint from the control arm with a ball joint fork or another suitable tool.

To install:
Installation is the reverse of removal but please note the following important steps.
  1. On R-series vehicles, start the new ball joint into the control arm. Position the bleed vent in the rubber boot facing inward.
  2. On C-series vehicles, force the ball joint into position using a screw-type forcing tool. The ball joint will bottom in the control arm. The grease seal should face inboard.
  3. On R-series vehicles, turn the screw until the ball joint is seated in the control arm.
  4. Lower the upper arm and match the steering knuckle to the lower ball stud.
  5. On C-series vehicles, start ball stud into the knuckle. Install the nut and tighten it to 90 ft. lbs. (122 Nm) on 1988-90 models; 84 ft. lbs. (115 Nm) on 1991-94 models and 94 ft. lbs. (128 Nm) on 1995-98 models. Advance the nut to align the cotter pin hole and insert the new cotter pin. NEVER back off the nut to align the cotter pin hole; always advance it!
  6. On R-series vehicles, tighten the ball stud nut to 80-100 ft. lbs. (108-135 Nm), plus the additional torque necessary to align the cotter pin hole. Do not exceed 130 ft. lbs. (176 Nm) or back the nut off to align the holes with the pin.
  7. Install a new lube fitting and lubricate the new joint.

Jan 15, 2010 | 1996 GMC Sierra

1 Answer

I cant seem to remove the ball joint on my 96


the lower joints are pressed into the lower arm from the bottom, and they are in TIGHT, try suppporting the control arm under the spring mount and banging it out with a heavy hammer or at least loosten it a bit, the new one must be pressed in, make sure it goes in even all the way the lip must be flush, grind the rivets from the upper and install the new one with bolts supplied, its a lot of work for a diy

Nov 26, 2009 | 1995 Buick Roadmaster

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...