Question about Mercury Cars & Trucks

Open Question

Hex wrench size for caliper removal/1994 grand marquis

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: Instructions for removing the rear disc brake pads

7mm

Posted on Apr 22, 2009

Ad
daddyo44
  • 2 Answers

SOURCE: bolt size for 96 chevy front caliper

2002 Trailblazer - 4 bolts on caliper. I loosened the top bolt with the pin, but when I try to loosen the bottom, it feels like I'm tightening it. Do I need to loosen all 4?

Posted on Jul 16, 2009

  • 297 Answers

SOURCE: 2005 grand caravan ? size allen wrench to remove rear calipers

6 mm to small 8 mm to big, how about 7 mm would you not think ??

Posted on Aug 16, 2009

MNfisherman
  • 11896 Answers

SOURCE: what size wrench to remove brake calipers

Usually about 9/16. It should be SAE not metric, but if the standard is slightly loose, then you may be best off switching to metric socket.
You can go to autozone.com and register for full free online repair manual for your car. With everything you could need.

Posted on Dec 12, 2009

  • 2448 Answers

SOURCE: What size hex wrench is needed to remove front

Off the top of my head i belive its 3/8 ths inchi haven;t had to do mine in a few years I just checked its 3/8ths

Posted on Nov 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size Allen wrench for 2001 escape front caliper?


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Mar 11, 2012 | 2001 Ford Escape

1 Answer

What size wrench is reqired to remove the calipers


You will need a 9mm hex to take the screws out that hold the calipers on. Not a common size, so you may have some searching to do. I found mine at Napa Auto Parts.

Jan 23, 2011 | 2004 Ford Escape

1 Answer

What size hex wrench is needed to remove front brake calipers ?


Off the top of my head i belive its 3/8 ths inchi haven;t had to do mine in a few years I just checked its 3/8ths

Nov 22, 2010 | 1994 Chevrolet C1500

2 Answers

What size allen wrench to remove front brake caliper


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Oct 19, 2010 | 2005 Ford Escape

1 Answer

I need to know what size hex or allen wrench is needed to remove the front disc brake pads ,on a 1995 mercury villager.Thanks ! Jerry


I'm guessing 7 mm torx from factory, but some are hex after calipers are replaced. Maybe 8 mm hex.

Jan 21, 2010 | 1995 Mercury Villager

1 Answer

I can't disconnect the rearview mirror from the metal base on a 1994 Grand Marquis.


There is a set screw of some sort that you must loosen. Normally it is a hex head screw.

Dec 28, 2009 | 1994 Mercury Grand Marquis

2 Answers

How do you instal a crank shaft positioning sensor in a 1994 jeep grand cherokee?


there is an up dated sensor that you can purchase it fits on the pas side rear of engine at the trans bell housing near the top 2 13m wrench size bolts hold it on wiring harnes goes up and over motor then plugs into harness its a tight fit to get to on some engines

Oct 05, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Allen wrench size to fit caliper mounting bolt


some are 7/16 and some are 3/8 amd some are torx

May 30, 2009 | 1994 Chevrolet Corsica

2 Answers

1993 mercury grand marquis


If you are just removing and replacing the pads, you will need, i believe a 13mm wrench, a screw driver (flat head) and a "turn in caliper compression tool" because your rear calipers also act as your emergency brake when it's engaged. You will see 2 divits across from eachother on your caliper piston. Once you have the tool inplace and the slots lined up with the tool, turn clockwise and turn the caliper piston in. If it will not turn, then it's defective and will need to be replaced before you can install the new pads. If you need a turn in caliper tool, you can rent one at any autozone or advance auto, pay for it up front and get a complete refund when you are done and bring it back.
Good luck!

Dec 17, 2008 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

fordexpert

Level 3 Expert

5575 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...