Question about 1998 Chevrolet Blazer

4 Answers

What transmission interchanges with a 98 4z`x4 Blazer

Need to know what transmission will interchange with my 98 Blazer 4x4

Posted by on

  • 3 more comments 
  • Anonymous Jan 04, 2009

    i found a transmission out of a 98 bravada and need to know if this will bolt into my blazer because the bravada does not have buttons on the dash and the transmission is called a samrt transmission where my blazer has buttons on the dash for a four wheel drive will this work with my electronics My blazer is a 98 4x4

  • Anonymous Feb 19, 2009

    will a transmission out of a 1996 jimmy fit in on a 1998 blazer

  • Anonymous May 06, 2009

    Will a transmission from a '94 Blazer fit into my '98 Blazer?

  • yadayada
    yadayada May 11, 2010

    all trans's with a chevy bolt pattern will bolt up and work, as far as electronic controls go only the late model 4LA60 will work.

  • Anonymous Mar 12, 2014

    got a 2001 chev blazer needs alternator, got a 2002 and a 2000 chev blazer alternator to choose from

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Sorry but your stuck with the 4l60e if you want it to be right. as for using the bravada transmission thats fine you just have to use your transfer case. your transfer case uses a switch on the dash and an electric motor on the transfer case. the bravada uses a series of sensors on the front and rear axle that sense wheel slippage and send a signal to the electric motor on the transfer case causing it to lock in four wheel drive. when the sensors dont sense wheel slippage any more the system returns to two wheel drive. that,s why they call it smart track. just unbolt your transfer case from your transmission and bolt it to the bravada transmission and install it. p.s- dont forget to at least change the front pump converter seal. for 4 or 5 bucks it,s cheap insurance against a major leak and i dont think you want to pull that transmission out again and yes i saw that happen to many times. good luck.-G.J.M

Posted on Feb 08, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Your best bet would be another 98 Blazer/Jimmy transmission, or you would want to find the code "8TAD" on the laminated sticker next to the vent tube, or on the underside by where the 2wd transmission mount bosses are. The 96-97, 99-00, and 01-02 Blazer/Jimmy transmissions all have different valve bodies, and separator plates are all different, and in 99 they started to use the deep pan. The 98 was basically a one year only setup for that particular valve body/separator plate setup. You could use safely any 96/98 Blazer/Jimmy transmission. You just want to make sure it has the TAD behind the year (6TAD, 7TAD, 8TAD)

Posted on Apr 22, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

The 98 AWD transfer case is full time they didn't use the electroic till 99and up .

Posted on Apr 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 180 Answers

96 up 4L60E

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 02 blazer i want to put a motor out of a 98 in it will it interchange


Chevy Blazer Engine Swap Part 1 of 2 - YouTube

? 10:29
https://www.youtube.com/watch?v=Dt_7AKP2WcI
Aug 13, 2011 - Uploaded by Dave R
Replacing the engine in a mid-size Chevy Blazer 4x4 with oneout of a Jeep Cherokee 2wd. Original engine was low and motoroil and spun a bearing. ... Chevy Blazer Intake Gaskets Replaced & Cooling System Rebuilt - Duration: 16:45. by ... 4:02. 94 4.3l Vortec V6 GM (black motor) - Duration: 6:01. by ...

4.3 vortec engine removal - YouTube




Jan 01, 2016 | Cars & Trucks

2 Answers

What can interchange with 1989 chevy s-10 Blazer (front spindle)


if its rwd then your golden if its 4x4 you might be ok. If 4x4 and engines and trannys don't match, good luck, tell us how you do. interchange-1989-chevy-s-10-blazer-front-l0u5xrrbjmm23votbgnhzwek-1-0.jpg

Jan 12, 2015 | Cars & Trucks

1 Answer

I have an 89 S10 Blazer. Can I replace the front wheel spindle with one from a 94 Jimmy blazer


If it is a 4x2, yes. If it is a 4x4, maybe. if same engine and tranny in both they will interchange on a good day. If not the same engine and tranny, 4x4 will probably not swap.

Jan 12, 2015 | 1989 Chevrolet S-10 Blazer

1 Answer

4l60e interchange


Sounds like you already have the 98 trans if you look at the Trans I.D. tag and the #'s are the same on yours and the 98 then it will work if not it will not operate properly. How do you know the trans is bad and please don't take this wrong I'm just asking ?? because you don't give enough info for diagnosis.

Jan 02, 2014 | Cars & Trucks

2 Answers

NEED TO KNOW WHAT TYPES OF TRANSMISSION WILL FIT IN MY S10 4X4 BLAZER


Well if you can find one from like a 4x4 s10 around the same year it will fit

Mar 18, 2013 | 1995 Chevrolet Blazer

2 Answers

1996 s10 blazer 4x4 automatic transmission going bad what years will interchange


u might what to repost ur ? because u need to know the 8th vin# has to be the same as well as the years have to inter change

Dec 10, 2010 | 1996 Chevrolet Blazer

1 Answer

Transmission interchange


Yes, but the steps involved in switching the 4wd output shaft, over to the 2wd output shaft are very involved. Thats assuming that the bellhousings are identical. (detachable bellhousing) That you do not need a 30 spline input shaft for your torque converter (96+ blazer input shaft splines are all 28 splines, however you may need a 30 spline in order for the correct torque converter to fit your 2wd vehicle.) You will need to know what 2wd output shaft you need, there are quite a few variations. Then you would need to take the pan off, pull the shift soleniod blocking access to the lockup soleniod, remove the lockup soleniod, remove the pump bolts, pull the pump, unhook the 2nd/4th, band remove the reverse drum - 3/4 drum (by pulling the input shaft twards you) then remove the yellow snap ring holding the output shaft in place. Now the output shaft is able to be removed and switched. Re instalation of the drums/pump is tricky as well, as all the clutches need lined back up to slide back onto there corasponding splines. Long story short, it would be alot more trouble than its worth. : )

Apr 02, 2009 | 1996 Chevrolet Blazer

2 Answers

94 Jeep Grand Cherokee Transmission Problom


1994 is the same as 1997. parts are interchangeable

Dec 31, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

2,455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...