Question about Cars & Trucks

Open Question

JCB 214 series s wont shift into gear. broken wires

Some one cut the wires and all are yellow need a schematic to rewire shift solonoid so it can shift into gear

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: drivers side power window needs

1. Go to ...
2. Enter the following as the code: pl249412345678
3. Click on Auto Repair Reference Center near the top of the page
4. And you're in! find your model, year, make etc...

They have wiring diagrams for the power windows for the Safari along with a lot of other good manuals and diagrams.

Posted on Dec 03, 2008

  • 7 Answers

SOURCE: 1996 Jetta won't shift into drive all other gears

VW Automatic transmissions must be filled within a specific level or they will not shift. Also, must have VW special transmission fluid or ATF +4 FULL SYNTHETIC!!! Required to create proper internal pressure...

Posted on Apr 08, 2009

  • 290 Answers

SOURCE: wiring schematics for 89mustang 2.3

check the "repair info" section at or try your local library for a Chilton or Hayes repair manual

Posted on Apr 15, 2009

  • 1 Answer

SOURCE: 1981 ford truck alternator schematic

replace an alternator on a 1981 ford f-150

Posted on Aug 05, 2009

  • 52 Answers

SOURCE: Dodge transmission

check the throttle valve cable on passenger side of throttle body

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1994 jcb 214 sitemaster backhoe steering is stuck in crab mode and will only move second gear but if I step on the brake it work in all gears

Sounds like you have a sensor wire crossed or out of connection. Touching the brake makes the brake light come on and is doing a re-connect. Check that out, it's gotta be in the electrical system as you can now understand. Something is crossfeeding and/or backfeeding power to where it shouldn't.

Aug 17, 2017 | Cars & Trucks

1 Answer

How do I fix the transmission in a 94 Cougar XR7 4.6 V8 that wont shift pass second gear.

It is very likely that a complete rebuild is needed along with a flush out of debris and a new torque converter.

May 17, 2016 | Cars & Trucks

1 Answer

JCB 214 series 3 will not move in forward or reverse

The problem is serious and needs a factory trained technician to trace the problem with test equipment that you do not have.

Jan 05, 2015 | Cars & Trucks

1 Answer

I have a JCB 214 series 3 1995 it will not move it was working fine going forward and reverse then it just stopped and it was always kind of hard to switch into different gears but now it just slips very...

Needs a clutch. Not cheap your gonna have to pull the transmission the clutch pack is reasonable 150.00 to 225.00 its the labor that is expensive. Don't recommend doing it yourself unless you are up to the task and have the ability and the tools,some special alignment clutch tools. ASE master certified mechanic.

Jan 05, 2015 | Cars & Trucks

2 Answers

Hi, In any gear, my 2003, 6 cy 4x4 explorer is jerking like the solenoid goes on and off without control... I aasume that it will bea guilty solenoid switch...Wha shall I do? Thanks

check the switch first to make sure you don;t have a broken or partly broken wire on the transmission connection and check for cracked vacume lines as well

Jul 11, 2011 | 2003 Ford Explorer

1 Answer

I have 97 jeep grand cherokee laredo v6 2wd all of the sudden if i shift into reverse it wont go anywhere but in park , neutral and all forward gears it wants to go forward ive been told it may be a...

To be honest with you Jeeps are notoriuse for their transmission problems.Most likely you have a shift solonoid in the transmission bad. I would have it checked before it gets worse to try and prevent internal problems.

Good Luck and I hope this helps you.

Oct 03, 2009 | 1995 Jeep Grand Cherokee

1 Answer

My 95 olds cutlass v6 3.1L sometimes wont shift out of third gear and it just completely shut off on the thruway... what does this mean?

Its possibly a bad shift solonoid on the trans itself. These trannys' 4T60E have 3 solonoids for shifting 1 for 1st and 2nd, 1 for 2nd to 3rd, and 1 for 3rd to overdrive. Its quite possible that the valve is sticking in the valve body. This can be a somewhat difficult job to do. But the solonoids arent that expensive. I would suggest a trans fluid flush and a new screen/filter and see if that helps. If you take it to a dealer the solonoid/s replacement will be around $800 or more.

Jul 22, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

1996 Jetta won't shift into drive all other gears

VW Automatic transmissions must be filled within a specific level or they will not shift. Also, must have VW special transmission fluid or ATF +4 FULL SYNTHETIC!!! Required to create proper internal pressure...

Mar 29, 2009 | 1996 Volkswagen Jetta

2 Answers

1991 Eclipse 2.0 Turbo not shifting, transmission stays in 1st gear

it sounds like the mechanic didn't properly adjust the inhibitor switch and transmission control cable.

Jul 15, 2008 | 1990 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides