Question about 2001 Ford Windstar

Open Question

2001 ford windstar compass not working

Keep wanting to calibrate and display says check compass. Where is compass located?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: change oxygen sensor 2001 ford windstar

fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Posted on Jan 01, 2009

Ad
  • 105 Answers

SOURCE: 2001 Ford Windstar runs rough.

remove the coil pack and look at bottom of it if it shows any cracks coil is bad very common on these vans if you have a noid light check for injector pulse on #4 if you have pulse and good blue spark most likely the injector is bad you have to remove upper plenum to get injectors out let me know how you make out

Posted on Jun 04, 2009

smartr10U
  • 1305 Answers

SOURCE: Battery keeps dying on 2001 Ford Windstar.

Check your battery terminals make sure they are clean and corrosion free.
Also check all ...A-L-L courtesy lights in your car. there are some ceiling mounted lights that are passenger operated and may be on... Also check your glove compartment and consoles for lights.
Also check for charger cords... These have indicator lights and sometimes can drain the batt as well.
Also, under the hood, is a gravity activated lamp . Open the hood and make sure that it's going off and staying off as the hood closes...
Let me know if you find anything...
K

Posted on Jul 28, 2009

  • 270 Answers

SOURCE: power steering pump on a 2001 ford windstar

There is a special tool for that. It should be available at most auto parts stores.

Posted on Oct 17, 2009

Dak408
  • 277 Answers

SOURCE: location of fuel pump fuse on 2001 ford windstar

see fuse box diagram for relay/fuse location under hood.
35b0f4b.gif

Posted on Oct 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2007 checy impala read "calibration complete" what does that mean ????


CALIBRATION COMPLETE
Refer to Electronic Compass Calibration do you have an owners manual ?
Compass Calibration
The compass direction will show CAL if it needs to be calibrated. Before calibrating the compass, drive the vehicle to an area that is magnetically clean (free of large metallic objects).
  1. Turn ON the ignition.
  2. Before calibrating the compass, make sure the compass is set to the variance zone in which the vehicle is travelling. See Compass Magnetic Variation Adjustment below.
  3. Press the vehicle information button until the PRESS TO CALIBRATE COMPASS screen is displayed.
  4. Press the set/reset button to start the compass calibration.
  5. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE when the calibration is complete.

Oct 02, 2016 | 2007 Chevrolet Impala

1 Answer

What is calibrate compass on 2004 Buick Rendezvous


Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode. 2. Press and hold the SET button for longer than three seconds. ZONE # PRESS & HOLD SET TO CHANGE: This display mode will be displayed when you are manually calibrating the system. The current zone number for compass variance will be displayed in place of the # symbol. Use the SET button to select the zone number from the graphic shown to select the current area of the country that you are driving in. PRESS SET TO CALIBRATE COMPASS: After selecting your zone, press the MODE button and this will be displayed on the DIC. Press the SET button and complete three 360 degree turns in an area free from large metal objects. The following two messages will toggle in the display until you calibrate the compass: • DRIVE VEHICLE IN CIRCLE • CALIBRATING COMPASS When calibration is complete, the display will return to its normal mode. 3-61 info obtained from MANUAL OWL
press the helpful button and follow me on fixya for more tips

Compass Variance Zone Procedure DIC Compass Driver Information Center DIC...

http://www.manuals365.com/swf/buick/2004_buick_rendezvous_owners.html?page=200

http://repair.chiltondiy.com/Buick/Rendezvous/Repair-Manual-Online
http://www.repairservicemanuals.com/Buick

Feb 02, 2016 | Buick Cars & Trucks

1 Answer

What is calibrate compass on 2004 Buick Rendezvous Vous


Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode. 2. Press and hold the SET button for longer than three seconds. ZONE # PRESS & HOLD SET TO CHANGE: This display mode will be displayed when you are manually calibrating the system. The current zone number for compass variance will be displayed in place of the # symbol. Use the SET button to select the zone number from the graphic shown to select the current area of the country that you are driving in. PRESS SET TO CALIBRATE COMPASS: After selecting your zone, press the MODE button and this will be displayed on the DIC. Press the SET button and complete three 360 degree turns in an area free from large metal objects. The following two messages will toggle in the display until you calibrate the compass: • DRIVE VEHICLE IN CIRCLE • CALIBRATING COMPASS When calibration is complete, the display will return to its normal mode. 3-61 info obtained from MANUAL OWL
press the helpful button and follow me on fixya for more tips

Compass Variance Zone Procedure DIC Compass Driver Information Center DIC...
http://www.manuals365.com/swf/buick/2004_buick_rendezvous_owners.html?page=200
http://repair.chiltondiy.com/Buick/Rendezvous/Repair-Manual-Online
http://www.repairservicemanuals.com/Buick

Feb 02, 2016 | Buick Cars & Trucks

2 Answers

2006 Expedition overhead compass reads "N" when heading "E". Wonder how to reset it so it indicates the direction accurately.


Yes. Wish I could tell you which button for sure, but to reprogram the Compass you hold one of the buttons and drive in a circle one or two times to reacquire your position.

Apr 08, 2013 | 2006 Ford Expedition XLT

1 Answer

How do you calibrate the compass on a 2002 Ford Windstar


Copied from alldatadiy.com for 2002 Ford Truck Windstar V6-3.8L.....


Compass Calibration

1. Start the vehicle and locate the compass module mounted on the base of the mirror.

NOTE: For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essential electrical accessories (rear window defrost, heater, A/C, map lamps, wipers, etc.) and make sure all doors are shut.

2. Press the RESET button until RESET to CAL is displayed in the message center display.

NOTE: To exit the calibration adjustment mode before carrying out a compass adjustment, turn the ignition switch to the OFF position.

3. Slowly drive the vehicle in a circle no more than five times at no more than 5 km/h (3 mph) until CIRCLE slowly changes to CALIBRATION COMPLETED in the message center display.

Jun 21, 2012 | Cars & Trucks

1 Answer

Our outside temperature display on our dash now says zone 9, not the outside temperature, on our 2002 Ford Explorer. How do we fix it to display the temperature again?


The zone nine is for the compass you need to calibrate the compass. and then you temp will work again. check the owners manual if you do not have one call the service department at a ford dealer they should be able to help you.

Feb 17, 2011 | Ford Explorer Cars & Trucks

1 Answer

I have 2002 Yukpn Denali XL. There is a OC code that appears in the rear view. What is the cause of this and how can I fix it?


The "OC" indicates your compass is "Out of Calibration". Below is the proceedure to recalibrate your compass.

Compass Calibration
The compass may need calibration if:
 After five seconds, the display does not show a
compass heading (N for North, for example), there
may be a strong magnetic field interfering with the
compass. Such interference may be caused by a
magnetic antenna mount, magnetic note pad holder
or a similar magnetic item.
 The compass does not display the correct heading
and the compass zone variance is set correctly.
In order to calibrate, the letters CAL must be displayed
in the mirror compass windows. If CAL is not
displayed, push in the COMP button for approximately
eight seconds or until the letters CAL are displayed.
The compass can be calibrated in one of two ways:
 Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display reads a direction, or
 drive the vehicle on your everyday routine and after
several turns the compass will become calibrated and
will display a direction.

Good luck.

Oct 23, 2009 | 2003 GMC Yukon XL

1 Answer

Compass wont calibrate


Check all your fuses. There is one that holds memory data.

Aug 04, 2009 | 2001 Ford F250 Super Duty Super Cab

2 Answers

Compass out of whack


You need to recalibrate the compass. The procedure is in your owners manual. Here are the basic steps.

First, you will need to verify that your compass zone is set to your current geographic location. Since I do not know where you are located, I cannot tell you the code. They are listed in the manual. (For example, So Cal is zone 5.)

Second, here is the compass calibration adjustment procedure:

Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
1. Start the vehicle.
2. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window.
3. Drive the vehicle slowly (less than 3 mph) in circles until CAL indicator turns off. As many as 5 complete circles may be required.
4. The compass is now calibrated.

Dec 19, 2008 | 2005 Ford F-150

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...