Question about 1988 Mazda B2200

Open Question

Where is headlight relay 1988 mazda b2200

Headlights quit working

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
betz73
  • 298 Answers

SOURCE: headlights 2000 mazda 626

try changing both headlight bulbs. If that does not solve the problem then have the relay's checked.

Posted on Oct 01, 2008

Ad
jingB
  • 19 Answers

SOURCE: mazda engine bad

yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Posted on Apr 14, 2009

scott586
  • 41 Answers

SOURCE: need to change headlight on 2003 mazda rx 6

If it is the headlight itself. There may be a cover or shroud on the front of the engin bay. Remove that, may be a combination of clips and screws. If it does not cever the light area, it is even easier. There will probably be 3 screws or nuts, remover these and unplug the electrical to the light. From there you should just be able to pop the light out of place. If you are just replacing the bulbs. Where the power goes into the assembly, turn the clip, may be grey in color and pull out of the headlight assembly and replace the light bulb. But don't touch the new bulb the oils from your skin will damage the bulb.

Posted on Apr 22, 2009

  • 1 Answer

SOURCE: Fan blower doesn't work

I have the same truck. Mine only worked on high. I replaced the blower motor resistor and it worked for a few seconds and then the resistor started to overheat and fry. I then removed the blower motor and found it to be pretty seized up so I replaced it along with another resistor and it works great. At any rate, be careful not to ruin a new resistor. If it shows any signs of getting hot when you first fire it up then turn off the blower motor immediately and replace it too. In my case, the worn out blower motor is probably what caused the original resistor and the replacement to fail in the first place.

Posted on Jun 30, 2009

  • 6 Answers

SOURCE: can a bad ignition switch cause the truck to die

Yes, bad ignition switch can cause that, did on my B2200.

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electrical Issues B2200


Your alternator is not yet doing anything. Minimum voltage, even with all accessories on, should be around 13.5 volts. Check all fuses, connections, grounds, and wiring. Have the alternator tested if you find nothing amiss.

Dec 03, 2012 | 1988 Mazda B2200

1 Answer

91 mazda b2200 one headlight is dimmer


Check the body ground of the "dimmer" light.

Oct 19, 2012 | Mazda Cars & Trucks

1 Answer

How to quiet noisey lifters


replace lifters or run diesel fuel thru engine at next oil change to remove sludge and coating on lifters

Mar 03, 2010 | 1988 Mazda B2200

1 Answer

Speedometer and odometer stopped working


need a new speedo cable from tranny to back of dash

Feb 25, 2010 | 1988 Mazda B2200

1 Answer

89 mazda b2200 everytime i turn my lights on i blow the fuse to my dash and driving tail lights can any body help


might be an exposed power wire to your lights grounding out. check your headlight wires for this.

Feb 03, 2010 | 1988 Mazda B2200

1 Answer

1989 mazda b2200 electrical problem


Hi,I would check the fusible links at the battery positive terminal.They look like normal wires but can burn out and leave the insulation intact.Try to stretch them,you will find the dead one.

Jul 19, 2009 | 1988 Mazda B2200

1 Answer

1988 Mazda B2200 starts well, but as it warms up, the gas flow stops. I changed the fuel pump and the problem still persists. Always starts.


I would trying to either checked fuel filter or if that dosent work chang the fuel pressure regulator.

Jul 19, 2009 | 1988 Mazda B2200

1 Answer

Can a bad ignition switch cause the truck to die or idle bad? 1988 mazda b2200


Yes, bad ignition switch can cause that, did on my B2200.

Apr 16, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...