Question about 2004 Jeep Liberty

Open Question

Removing front axle from 2004 jeep liberty

How to remove

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: How can i remove the evaporator from a 2002 jeep liberty

quite the project. go to autozone, online. go to repair guide section, and lookup heater core replacement, same area as evap and easier for you to follow, than my directions. good luck glenn

Posted on Feb 07, 2009

  • 6982 Answers

SOURCE: 2003 V6 Jeep Liberty Limited how do I remove front brake rotor

Hole with notches is likely a torks screw Looks like an allan key hole with extra splines? they make a bit that fits in there. It's on the flat surface where the wheel mounts right?

Posted on Apr 22, 2009

  • 1 Answer

SOURCE: 2004 jeep liberty thermostat change?

ihave to change my thermostat in my 04 jeep liberty is it hard

Posted on May 22, 2009

  • 1146 Answers

SOURCE: how to change out thermostat on 2002 jeep liberty?

Hi:
You don't need to remove the water pump. The thermostat is located under a housing, at the engine end of the upper radiator hose.

All you need to do is drain your radiator, remove the upper radiator hose, and remove the thermostat housing. Clean it up well, and replace all gaskets before reinstalling!

Posted on Nov 30, 2009

  • 13 Answers

SOURCE: 2004 jeep overland rear axle seals are leaking.

Yes. The c lock needs to come off.

Posted on Dec 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 jeep liberty front seat removal


left or right?
battery neg lug off.
all connectors under seat ,unplugged
then the 4 bolts out
KJ jeep SM serv, man.covers this.
chapter 23 page 78

cut > paste


seat-x4dybgm1xaxinyj1r3jreevk-4-0.jpg

Feb 20, 2017 | 2004 Jeep Liberty

1 Answer

Front seat removal 2004 jeep liberty


4 bolts.
look first see em,' you will of you look
if wanting to know before looking
there is this magic book, called SM
that does this step by step,
see KJ jeep and read.
http://jeepdied.com/books.html

Feb 20, 2017 | 2004 Jeep Liberty

1 Answer

I have to lower the front crossmember to remove the oil pan. Is there any precautions I should know about? It is on 2004 jeep liberty 4x4


no engine stated, they even have diesel. or 3.7L GAS.
I toss my first coil, land on 3.7L V6.
great question, like the very first ever.
most just do it and get in trouble. vast posts in this.
but whats up, what is wrong, what part failed.?
this is best to know, so we can send you the official chapter on this from jeep.
sure use jackstands, never jacks only and never bricks .
04,KJ jeep 4wd pan off.
in chapter 9 ,under diagnostics, and pan leaks. that?
it says read
Refer to 9 -
ENGINE/LUBRICATION/OIL PAN -
REMOVAL). page 1555 (3.7L)
and i quote:
REMOVAL
1. Disconnect and isolate negative battery cable.
2. Install engine support fixture.
3. Raise and support vehicle.
4. Remove front wheel assemblies.
5. Remove skid plate (if equipped). (Refer to 13 -
FRAME & BUMPERS/FRAME/FRONT SKID
PLATE - REMOVAL)
6. Drain engine oil.
7. Mark adjustment cam position of front lower control
arm bolts.
8. Remove front lower control arm bolts. (Refer to 2 -
SUSPENSION/FRONT/LOWER CONTROL ARM -
REMOVAL)
9. Disconnect LH tie rod. (Refer to 19 - STEERING/
LINKAGE/TIE ROD END - REMOVAL)
10. Disconnect LH lower ball joint (Refer to 2 - SUSPENSION/
FRONT/LOWER BALL JOINT -
REMOVAL)
11. Disconnect LH strut clevis (Refer to 2 - SUSPENSION/
FRONT/CLEVIS BRACKET - REMOVAL)
12. Remove LH front axle (Refer to 3 - DIFFERENTIAL
& DRIVELINE/HALF SHAFT - REMOVAL)
13. Remove front axle brace bolts.
14. Remove front prop shaft. (Refer to 3 - DIFFERENTIAL
& DRIVELINE/PROPELLER SHAFT/
PROPELLER SHAFT - REMOVAL)
15. Drain front axle.
16. Using a transmission jack, support front axle.
17. Remove axle bracket bolts. (Refer to 3 - DIFFERENTIAL & DRIVELINE/FRONT AXLE - REMOVAL)
18. With RH axle still in place, remove front differential.
19. Remove transmission oil cooler line bracket.
20. Remove engine to transmission stiffening bracket.
21. Position Special Tool 8534 on fender lip and align the slots in the brackets with the fender mounting holes.
22. Secure brackets to the fender using four M6 X 1.0 X 25 MM flanged cap screws.
23. Tighten the thumbscrews to secure the sleeves to the support tube.
24. Secure the support tube in an upright position.
25. Assemble the flat washer, thrust bearing, hook and T handle.
26. Using the M10 X 1.75 mm flanged nut supplied with the support fixture, secure the chain to the front engine
lifting stud.
27. Loosen engine mounts.
28. Remove oil pan bolts.
29. Seperate oil pan (1) from engine.
30. Move oil pan to one side, remove oils sump bolt and windage tray bolts,
NOTE: Do not pry on oil pan or oil pan gasket. Gasket is integral to engine windage tray and does not come
out with oil pan.
end quote, (off)

Nov 30, 2016 | 2004 Jeep Liberty

1 Answer

Replace rear wheel seal on jeep lberty


06 lib
fsm book shows this as does alldata.com
so?
you want me to look for you?
i dont post R&R
just removes and at that point, hope its obvious.....

l & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. With vehicle in neutral, position vehicle on hoist.
  3. Remove differential housing cover and drain lubricant.
  4. Rotate differential case so pinion mate shaft lock screw is accessible. Remove lock screw and pinion mate shaft from differential case.
  5. Push axle shaft inward and remove axle shaft C-lock from the axle shaft.
  6. Remove axle shaft from side gear and axle tube.
  7. Remove axle shaft seal from axle tube with a seal pick.
To install:

Jul 10, 2014 | 2006 Jeep Liberty

1 Answer

2005 jeep liberty 3.7 4wd front hub assembly. able to remove all components execpt the hub assembly bolts. Are they splined or 6 point. And what mm or sae are they. It's a bitch to see them.


the car is metric, so forget SAE.
what are you doing, why not post the service or problem. so we can play on same page??????
the dealer parts pages (and FSM) show the parts there.
the front axle
let me take a wild guess..... bad hub bearings, right?
so there are just 2 steps, in the FSM.
what are they? (ill assume , wheel off, calipers off. and rotor.)
1: remove nut 9
2: then with slide hammer attached to studs, of #5; remove hub from axle.
if lucky, no rust? LOL, i can hit it with 2x4 or rubber mallet and bam
its off. but luck runs low in the salt belt, (LOL) or driven on ocean beaches.


why not buy and FSM and be ready all the time.
or log into alldata.com
(can be seen at any dealer at any time...)

http://www.factorychryslerparts.com/showAssembly.aspx?ukey_assembly=537636&ukey_make=1064&ukey_model=15531&modelYear=2005&searchString=hub

Aug 08, 2013 | 2005 Jeep Liberty

1 Answer

Can I replace the front diff isolator bushes on my uk 2004 cherokee sport 2.8crd without dropping the front axle?


No-- I doubt you would have room & without seeing what
your referring to ,I think you need special tools to press
them out.

No one,absolutely no one would buy those tools

Maybe a dealer has something the manufacturer
requires a dealership to have

Nov 20, 2012 | 2004 Jeep Liberty

1 Answer

How to remove wheel hub assembly on jeep liberty


take the axle nut off and take the spindle off off.on the back of the spindle you will find three bolts.Remove the bolts and beat the hub and bearing out. the new one will go right in. not a hard job

Dec 29, 2009 | 2002 Jeep Liberty

1 Answer

Heater only works on 3 and 4 setting


Your heater motor speed selector only working on a couple levels is caused by a faulting blower motor resistor.This part is located on the evaporator case next to the blower motor itself.Two bolts remove the resistor and an electrical pigtail finishes it off.The location of this is underneath the dash on the pass front side.Happy Holidays!!

Dec 10, 2009 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty front suspension seems to lock up front tires while making a turn WTF????????


Sounds like the tires are hitting the wheel wells. THis is Deadly.

Do you have oversize tires on the Jeep? Is your front axle drive engaged? Is it slung low to the ground like a low-rider? Any of these can cause 'lockup' in the front end when turning. If not, I would have the U-joints, CV joints and drive linkages checked.

Mar 27, 2009 | 2004 Jeep Liberty

Not finding what you are looking for?
2004 Jeep Liberty Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...