Question about 2004 Chevrolet S-10

1 Answer

Cd holder How do I take out the cd holder in the center console?

Posted by on

  • Chris McMahon Aug 24, 2013

    pull really freakin hard

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 69 Answers

Open the center console, there is a bucket in there, pull straight up on it and it will pop out of the console "frame". There is a open hole under it, there is clips on the sides of the CD disk case holder, push on it with a flat head and it will pop out.

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

I AM TRYING TO TAKEOUT A CENTER CONSOLE OUT OF A 2000 CHRYSLER INTREPID


Hi Ken, I'm glad to help! Ken I have removed so many of the center consoles on Intrepids, heck I can do it in my sleep. I'm not sure how far you have gotten removing it. But there are some hidden screws under the rear cup holder. Pull the rear seat cup holder out and there is one in the very front and 2 down inside the slot. Those are the only ones you need to remove the other screws simply hold the cup holder in. The rest of the removal is very easy. Hope this helps and have an awesome day Ken!

Apr 18, 2014 | 2000 Chrysler Concorde

1 Answer

Replacing cup holder


I assume you mean the one that flips up in the center console?

If so, there are three likely issues.

1) did you slide out the retainer from the upper screw? the top screw had a cover that had to be pried off. you then took the screw out. Lastly you have to slide out the plastic retainer that the screw went into. It slides out towards the opening.

2) you have to have the cup holder partially open to remove it. the hinged part that folds up is stored in the cavity under the console when closed. you have to open the cup holder and keep pushing until the front of the cup holder lip comes up. Work the cup holder up and down until it comes out.

3) the cup holder is stuck in place due to years of spilled liquid. If you've done the above, then you can either spray soapy water on the creases around the opening and let it set, or you can apply strategic brute force.
Be aware through. if this is the center console cup holder just behind the gear shifter. There are two screws and nothing else to hold it in. Just be carefull....

Mar 17, 2014 | Volvo S80 Cars & Trucks

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

How do you access the back of the radio/CD assembly? I assume the facing trim comes out somehow, but it's not obvious -


pull the cup holder , there is a litel trim of plastic pull that out and now you will see 2 screws
take them out and pull the reast of the center console
clips only

Nov 22, 2010 | 2004 Chrysler Town & Country

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

The light that illuminates the shifter position is out. Its an automatic transmission.


In the console shift, it is a light bulb in a holder.

Open the center console lid, and in the indent for the console cover / trim panel, pull up. The entire silver/gray colored cover ( where the cup holders are at ) will lift off.
You will see the light holder under the console trim plate ( the silver trim ring ).

Nov 23, 2009 | 2005 Ford F-150

1 Answer

Buick Regal cup holder problem


Yes absolutely you can my friend. and you are correct this will fit 1997 to 2004 actually!

Jul 10, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Dodge Center Console


When I told you to lube it, I was assuming you were talking about the cup holder in the center, lower part of the dash, if I was correct then the proper way to open it if its working properly is the push in on it and then it should come down to expose the cup holders. To close it you lift it and push in on it to lock back in the upright position.

You were speaking of the cup holder correct?

Waiting for reply!

Dec 30, 2008 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2004 Chevrolet S-10 Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...