Question about Mitsubishi Cars & Trucks

Open Question

What is a 2005 mitsubishi l300 van radio code

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: heater wont blow hot air in van. How do i fix it?

add coolant to the radiator and it should help circulate it and warm the air up

Posted on May 07, 2009

Ad
mobilityGo
  • 68 Answers

SOURCE: where is the ignition fuse for a 2004 mitsubishi

you can buy them from most car shop

Posted on Dec 07, 2009

  • 978 Answers

SOURCE: my Mitsubishi l300 van wont go in to fourth gear

check gear linkage

Posted on Mar 03, 2010

  • 11800 Answers

SOURCE: Misubishi L300 sliding door

Any year door between 1979 and present will do, the basic shell of the car - including doors - hasn't changed.
For a perfect fit of the trim you should get one from 79 to 86.

Posted on Jun 04, 2010

swoop611
  • 488 Answers

SOURCE: I need a workshop manual

The mixture screw is located in a resessed hole just above the therma start plate at the rear of the carby. The rear of the carby faces away from the inlet manifold and you require a special tool to access this adjustment. The other screw adjustments on the carby and linkages are for idle, fast idle, and choke limits including those models with automatic (thermal type) choke mechanisms.
I would advise that if you make any adjustments to the mixture that you have the mixture checked using an exhaust gas analyser.However, as a general rule of thumb, screw the mixture adjustment all the way in until you feel it tighten but DO NOT FORCE IT !! the screw has a delicate needle valve on the end which will be damaged if the screw is forced beyond it's normal length of travel.
Unscrew the mixture screw a total of one and a quarter turns back out and then have the setting checked with a exhaust gas analyser. Too rich and not only is this expensive but will cause damage to spark plugs etc. Too lean a setting will cause a misfire which will damage valves and pistons.

Posted on Mar 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i tune a 1988 Mitsubishi express van l300


Install new spark plugs, new spark plug wires if needed, a new gas filter, a new air filter if needed.

Jun 25, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where's the computer in an Mitsubishi 1993 L300 express van?


my guess is the pillar behind the drivers head behind the plastic covering.

May 21, 2015 | Mitsubishi Cars & Trucks

2 Answers

What is the pin code for a 2005 mitsubishi outlander


When you disconnect your battery and then reconnect it again, it disables the radio. This is an anti-theft protection for your car radio.
The enable your radio the activation code is in your vehicle owner's manual. If you do not have this code you need to go to your Mitsubishi service centre and get them to enter this code for you.

Feb 19, 2013 | 2005 Mitsubishi Outlander

1 Answer

My conpany just purchased 15 mitsubishi L300 vans. i need a parts manual and a service manuel. do you know were i can get one for download


go on line on internet look on ebay or look on internet for mitsubishi parts manual you should be able to find one.you can go to dealership try to order one.it will cost you. i have seen parts manual cost about $100.00

Apr 10, 2011 | Mitsubishi Cargo Cars & Trucks

1 Answer

Misubishi L300 sliding door


Any year door between 1979 and present will do, the basic shell of the car - including doors - hasn't changed.
For a perfect fit of the trim you should get one from 79 to 86.

Jun 04, 2010 | Mitsubishi Cargo Cars & Trucks

1 Answer

Heater wont blow hot air in van. How do i fix it?


add coolant to the radiator and it should help circulate it and warm the air up

May 07, 2009 | Mitsubishi Minivan Cars & Trucks

2 Answers

Glow plug timer


check the temp sensor or low resistance in the glow plugs first

Jul 10, 2008 | Mitsubishi Minivan Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...