Question about 1996 Mitsubishi Galant

1 Answer

2004 Mitsubishi Galant A/C Light Blinking on Control Switch

My A/C Light is blinking on my control switch - compressor is running, freon is at correct level but still does not blow cold air.

Any ideas?

Posted by on

  • Anonymous Mar 13, 2009

    2004 mitsubishi galant A/C light blinking on control switch

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just had same problem with mine. Turned out the condenser was bad.

Posted on Jun 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my AC compressor running when my temperature control is set to heat, fan control set to 2, AC control switch off and air flow control set for floor?


If you have an automatic climate system where you can set temp the the compressor will run at some of the middle settings. The system blends cold and warm air to obtain the desired temp setting. If it does not have automatic control you have another issue.

Oct 23, 2014 | 2003 Mitsubishi Galant

4 Answers

2004 sebring air conditioner stops and starts


Low freon will cause the compressor to short cycle, when the compressor runs the pressure in the low line is pulled down and the low pressure switch turns it off. Not running the pressure builds up and turns it back on. In the old days there was no low pressure switch, with no freon to carry the oil the compressor was destroyed.

Jun 28, 2014 | 2004 Chrysler Sebring

1 Answer

No power to compressor 2 pounds of Freon compressor, expansion valve, dryer condenser an high pressure switch new.


I would say that with 2 lbs of Freon in the system that the high pressure switch is stopping the compressor from working and being destroyed from liquid on top of the pistons. An ac system works by compressing gas to liquid and then releasing that liquid through a small orifice into a vacuum created by the ac compressor .With excessive liquid then that turning to gas situation will not occur and liquid will get to the pistons and stop the piston movement. I recommend that you take it to a ac specialist and have the system pumped down into a receiver tank and then the correct amount of refrigerant gas added .

May 14, 2014 | 2004 Mitsubishi Galant

1 Answer

A/C blowing cold air when car is cold, but clutch disengages when car heats up


Low of freon, have it charged to proper lvls with CORRECT freon/refridgerant

Dec 05, 2013 | Mitsubishi Cars & Trucks

2 Answers

Air conditioning system freon


You'll need to have a mechanic check the system to see if it is low on freon, or if you have an electrical problem.

Jun 09, 2013 | 2008 Mitsubishi Galant

1 Answer

I have a 2001 Ford Explorer. The A/C blows but air isnt cold.... Any ideas?


you need to check and see if the compressor is running, you should be able to observe this after opening the hood with the engine running look to see if the center of the compressor is turning while the air is turned on. All a/c auto systems have a low pressure switch which will not let the compressor run if there is not enough freon in the system . You will need someone with a/c experience to check freon levels .

May 13, 2011 | Ford Explorer Cars & Trucks

2 Answers

I also have a 2006 H3 that the air conditioning was working great and was blowing super cold. then for 2 days i would try to turn the air on and it wouldnt work until the H3 was running for 10mins then it...


is freon level correct. does compressor come on when turned to cold? if it doesn't freon may be low or compressor may be bad. theres also an outside possibilty of the control being bad.

Jan 17, 2011 | 2006 Hummer H3

1 Answer

AC light blinking


the a/c light is blinking because it has picked up slippage in belt or the compressor is not turning -locked up or belt missing

Jul 07, 2010 | 2001 Mitsubishi Galant

Not finding what you are looking for?
1996 Mitsubishi Galant Logo

Related Topics:

1,678 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...