Question about 2000 Chevrolet Venture

1 Answer

Heater fan not working in my venture

I replaced the blower resister and it still doesn't work?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mini relay

Posted on Nov 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: heater fan not working in 05 Chevy Equinox

I suspect you also checked the fuses, some vehicles are double protected, especially since you usually have to remove the entire dash panel to get to the heater fan blower motor. It should be in the middle or under the glove box, should be located in a plastic box that has like a bell shape to where the motor is. check fuses then check wiring, and make absolutely certain the relay was the correct one that you changed, in a 3 year old vehicle the fan motor should not be bad yet.

Posted on Jan 09, 2009

  • 6982 Answers

SOURCE: 1983 Chevrolet Suburban Heater fan not working

check relay and blower resistor...likely the relay is bad.

Posted on Mar 15, 2009

outdoorsman5
  • 631 Answers

SOURCE: The fan/blower only works on the high setting.

It probably is the fan switch itself. They are around $30. for a new one. You can take it out and check to see if you have power to all the settings with a ohm meter or test light. They are not real hard to take out.

Posted on Jul 28, 2009

  • 2 Answers

SOURCE: blower heater fan only works on 4, 1,2,3,and 5 don't work

check fan blower relay

Posted on Aug 29, 2009

emissionwiz
  • 76673 Answers

SOURCE: fan blower only works on high speed (4) not on any lower speeds

this is caused by the blower resistor as you correctly diagnosed, but the new resistor is blown because the fan motor is drawing to much current and blowing the resistor back out, replace the blower motor and resistor again.

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 venture blower motor won't shut off with the ignition


Could be something in the key switch I suppose. There is a high speed relay for the blower that gets power directly from the battery, but the other speeds should go thru the fan switch and get power from the key switch.

Jul 25, 2013 | Cars & Trucks

1 Answer

A/C Heater Amplifier/Resistor for Auto Climate Control


Does the Blower Motor work when power
is applied-- just to it?
Sounds like a high current draw on that circuit
Need wiring diagram & ability to know how to test
for the problem
I only work from factory diagnostic manuals & wiring
books- I buy for all my vehicles when they are new.
No way you can push & poke,wish & hope
You need to see the circuits on paper & have the
manufactures ideas on how to diagnose

Jul 17, 2013 | 2002 Nissan Maxima

1 Answer

Heater fan moter good put new switch in and fan doesn,t work


Could be the blower motor resister,it's located by blower motor,2 screw hold it on.Here's what it looks like.

Dec 03, 2012 | 1990 Toyota Pickup

2 Answers

My a/c (heater & Defrost) doesn't always work, could it be a fuse or the fan blower?


Check whether you might have bad connection or contact,or e ven bad switch.

Sep 03, 2012 | 2005 Kia Spectra

1 Answer

Heater / air conditioner fan control doesn't engage fan. Previously, it only worked in high speed.


I would replace the blower motor resistor first then see if that corrects this. The resistor is located next to the blower motor under the dash.

Jul 16, 2012 | Cars & Trucks

2 Answers

I replace the heater blower in my 1989 volvo 740, the heat is now working but the problem is that it only blows after i turn it on #4, doesn't work on lower settings, pls advise


Geraldine,I would venture that the resistor board,usually mounted near the blower motor,has almost gone all the way bad. Have someone check it. Of course,it could be the blower speed selector switch,but probably not.
don-ohio (:^)

Dec 01, 2011 | 1989 Volvo 740

2 Answers

1983 Chevrolet Suburban Heater fan not working


Heater blower motor resister is bad, replace, located under dash above heater motor.

Mar 15, 2009 | 1983 Chevrolet Suburban

7 Answers

Heater Control Switch Only Works on High


Your problem is probably a part called the heater resistor block or board. When this part burns out you will only have high speed on the fan. On my 1999 voyager it is located on the firewall and it snaps in a hole in the firewall. This is under the hood behind the alternator.
Mine had a multi pin black plug plugged into it. Unplug the plug and
you should be able to pull the block out insert new block and plug plug back in and it should come to life.

Jun 05, 2008 | 2001 Chrysler Voyager

Not finding what you are looking for?
2000 Chevrolet Venture Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...