Question about Cars & Trucks

1 Answer

Trouble removing starter. installation of new starter.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

What kind of vehicle there could be things you will have to remove in order to get to it

Posted on Nov 04, 2012

  • arlene mills Nov 04, 2012

    Yes there is but having dificulty with bracket on the firewall side. are thee only 3 bolts to remove bracket?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the starter on a 2007 honda civic


Starter Removal and Installation

Removal

1. Make sure you have the anti-theft code for the audio system and the navigation system (if equipped), then write down the audio presets.
2. Disconnect the negative cable from the battery first, then disconnect the positive cable.

3. Remove exhaust pipe A.

4. Remove the intake manifold bracket.

5. Remove the harness clamps (A) and harness connector (B) from each clamp.

6. Remove the two bolts securing the starter, then remove the starter from the engine.

7. Disconnect the starter cable (A) from the B terminal. Disconnect the connector (B) from the S terminal, then remove the starter.

INSTALLATION

1. Install the starter cable (A) and connector (B). Make sure the starter cable crimped side of the ring terminal faces away from the starter when you connect it.

2. Install the starter, then loosely install the upper mounting bolt (A) and lower mounting bolt (B).
3. Tighten the upper mounting bolt, then tighten the lower mounting bolt.

4. Install the harness clamps (A) and harness connector (B) to each clamp.

5. Install the intake manifold bracket.

6. Install exhaust pipe A. Use new gaskets (B) and new self-locking nuts (C).
7. Connect the positive cable to the battery first, then connect the negative cable.
8. Start the engine to make sure the starter works properly.
9. Enter the anti-theft code for the audio system and the navigation system (if equipped), then enter the audio presets.
10. Set the clock.

Dec 22, 2016 | Honda Cars & Trucks

1 Answer

How to remove and install a starter motor


It is impossible to provide a suggested diagnosis without knowing the YEAR, MAKE, and MODEL of your vehicle.
Beyond that, your question is far too vague.
Replacing a starter on MOST (not all) vehicles is a fairly straightforward procedure. It generally entails disconnecting the battery negative terminal, removing the sires from the starter, supporting the starter while removing two to four bolts, pulling the starter, then reversing the procedure to install the new starter installing starter shims to accommodate for any misalignment of the new starter.

May 15, 2015 | Cars & Trucks

1 Answer

Installing the starter


Inspect/Test/Service/Replace
  • If your testing indicates that the starter must be removed, the first step is to disconnect the negative cable at the battery.
  • It may be necessary to place the vehicle on a lift to gain access to the starter. Before lifting the vehicle, disconnect all wires, fasteners, and so on that can be reached from under the hood.
  • Disconnect the wires leading to the solenoid terminals.
  • To avoid confusion when reinstalling the starter, it is wise to mark the wires so they can be reinstalled on their correct terminals.
  • On some vehicles you may need to disconnect the exhaust system to be able to remove the starter.
  • Loosen the starter mounting bolts and remove all but one.
  • Support the starter while removing the remaining bolt.
  • Then pull the starter out and away from the flywheel.
  • Once the starter is free, remove the last bolt and the starter.
  • Once the starter is out, inspect the starter drive pinion gear and the flywheel ring gear.
f17-26.gif Starter drive and flywheel ring gear wear patterns. Courtesy of Ford Motor Company.
  • When the teeth of the starter drive are abnormally worn, make sure you inspect the entire circumference of the flywheel.
  • If the starter drive or the flywheel ring gear show signs of wear or damage, they must be replaced.
  • Reverse the procedure to install the starter.
  • Make sure all electrical connections are tight.
  • If you are installing a new or remanufactured starter, sand away the paint at the mounting point before installing it. Also, make sure you have a good hold on the starter while installing it.
  • Many General Motors' starters use shims between the starter and the mounting pad.
f17-27.gif Shimming the starter to obtain proper pinion-to-ring gear clearance. Courtesy of General Motors Corporation - Service Operation.
  • To check this clearance, install the starter and insert a flat blade screwdriver into the access slot on the side of the drive housing. Pry the drive pinion gear into the engaged position.
  • Use a wire feeler gauge or a piece of 0.020-inch (0.5080-mm) diameter wire to check the clearance between the gears.
f17-28.gif Checking the clearance between the pinion gear and the ring gear.
  • If the clearance between the two gears is incorrect, shims will need to be added or subtracted to bring the clearance within specs.
  • If the clearance is excessive, the starter will produce a high-pitched whine while it is cranking the engine.
  • If the clearance is too small, the starter will make a high-pitched whine after the engine starts and the ignition switch is returned to the RUN position.
  • Every starter should be bench tested after it is removed and before it is installed. to conduct a free speed or load test on a starter, see the free speed test

May 07, 2012 | 1989 Ford Bronco

1 Answer

Having trouble getting the starter removed to replace it with a new one


If you want your car to show top performance, then your engine starter must be in best condition. You can find reliable starter at http://www.autopartspoint.com/products/starter.html

Jul 14, 2011 | 2000 Mercury Grand Marquis

3 Answers

How do you tilt engine forward enough to replace alternator on a pontiac aztek and then how do you set the engine back on the mounts?


3.6L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.

  2. Disconnect the battery ground (negative) cable from the battery.

  3. Raise and support the vehicle.

  4. Remove the radiator air baffle.

  5. Remove the starter motor BAT terminal nut and electrical leads.

  6. Remove the starter motor bolts.

  7. Remove the starter motor.
    06025-aztek-g31.gif

    Starter motor mounting-3.6L engine

To install:

  1. Install the starter motor.


    NOTE

    Use the correct fastener in the correct location.


  2. Install the starter motor bolts. Tighten the starter motor bolts to 37 ft. lbs (50 Nm).

  3. Install the starter motor S terminal electrical connector.

  4. Install the battery positive cable and the BAT terminal nut to the starter motor BAT terminal. Tighten the starter motor BAT terminal nut to 115 inch lbs. (13 Nm).

  5. Install radiator air baffle assembly.

  6. Lower the vehicle.

  7. Install the battery ground (negative) cable to the battery.

Feb 07, 2011 | 2001 Pontiac Aztek

1 Answer

How long should it take to install a starter in a 2002 ford excursion?


If you do not have any trouble with removal and installation, it should take about 30 minutes. Sometimes the new starter will have slightly different dimensions and can be a tight situation to connect the wires and can increase the installation time. Hopefully, this will help you to FixYa problem!

May 15, 2010 | 2002 Ford Excursion

1 Answer

How do I replace my starter?


Open hood.
Disconnect negative (-) batter cable
Locate the starter (under vehicle).
Remove electrical connections. (be sure to remember/take a picture/ make a drawing/ or mark which wires go to what posts)
Remove mounting bolts.
Remove starter, replace with new starter
Install mounting bolts
Install electrical connections

Jan 06, 2010 | 1990 Chevrolet S-10 Blazer

1 Answer

Startup problems, at first no clicking or nothing 3rd time engine turned over but there was a high pitch wining i think from the starter itself pls help, Chef KB


It sounds like the starter solenoid has gone bad, Best thing to do is just to replace the whole starter. The starter solenoid is mounted on the starter, but to go through all that trouble to remove the starter, might as well replace the whole thing. Auto Zone carries the starter for your car and can give you the step by step instructions to get the job done with common tools. Good luck and when removing the old starter, take pictures with your cell phone to reference the wires when re-installing the new starter.

Nov 24, 2009 | Buick Regal Cars & Trucks

3 Answers

How to replace the starter for a 95 buick lesabre


Be sure to disconnect the battery first. There are HOT wires connected to the starter. Disconnect three wires and two mounting bolts. It can be difficult to reach a wrench in there.

The new starter will come with shims, thin strips of metal. These are for getting the right distance between the starter gear and the flywheel. Hopefully you won't need them. But if the new starter is noisy when mounted, shim it some.

Jun 02, 2009 | 1995 Buick LeSabre

2 Answers

What procedures do I take when removing and installing a new starter? 1991 lexus ls 400


Let engine cool down, remove battery terminals (negative first, then positve), remove starter. Install starter, install battery terminals (positive first, then negative), start and check for proper operation (no grinding noise or squeling).

Apr 03, 2009 | 1991 Lexus LS 400

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...