Question about Nissan Cars & Trucks

Open Question

2000 Honda CRV oil pan gasket replacement

Oil Pan is blocked by part of the exhaust. How difficult is it to replace the oil pan gasket?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
picatudo
  • 239 Answers

SOURCE: 1999 OIL PAN GASKET

you have to remove exhaust

Posted on Jan 05, 2009

Ad
  • 1596 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000








Removal Procedure

Important: The original oil pan gasket is retained and aligned to the oil pan by rivets. When installing a new gasket, it is not necessary to install new rivets.
DO NOT reuse the oil pan gasket. When installing the oil pan, install a NEW oil pan gasket.

Caution: Refer to Battery Disconnect Caution in Service Precautions.

  • Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure
  • Remove the front differential if equipped with four wheel drive. Refer to Differential Carrier Assembly Replacement in Front Axle.
  • Remove the under body shield from the vehicle
  • Remove the oil pan underbody shield.
  • Remove the cross brace if equipped.
  • Drain the engine oil and remove the engine oil filter. Refer to Engine Oil and Oil Filter Change
  • Remove the lower transmission-to-oil pan bolts
  • Disconnect the oil level sensor electrical connector.
  • Remove two front wiring harness retainer bolts.


10. Remove the engine wiring harness retainer bolts from the engine oil pan.
11. Remove the engine oil cooler pipe to oil pan bolt.
12. Remove the transmission oil cooler pipe retainer and the bolt from the oil pan.
13. Remove the starter motor. Refer to Starter Motor Replacement.
14. Remove the left closeout cover and bolt.
15. Remove the engine oil pan. Refer to Oil Pan Removal.

Installation Procedure

Important: The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission bellhousing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan must NEVER protrude beyond the engine block and transmission bellhousing plane.

Will Send Remainder in another this place dont take kindly to larg files Your Email Address would realy be Better Then I could send Pictures Also up to YOU

Posted on Jan 27, 2009

landsend
  • 1066 Answers

SOURCE: How hard is it to replace the oil pan gasket in a Honda CRV 1998?

That depends on the clearance you have to remove and reinstall the oil pan.  Sometimes components and chassis get in the way and you either have to jack up the engine or remove the offending parts.
Also many newer cars don't use a gasket and only use a quality sealer.   Having a hoist is a definate plus

Posted on Mar 12, 2009

mcdevito75
  • 1970 Answers

SOURCE: How difficult is it to replace the oil pan gasket

mcdevito75 Here, Very difficukt, let a shop do the job.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove a 2005 cr-v honda oil pan


Remove all bolts in the pan assembly. You may need to remove other objects that may obstruct the removal of the oil pan bolts. It would be a good idea to have the oil drained prior to pan removal. The oil pan uses a special RTV sealant instead of a gasket and can be a pain to seperate from the engine block. Use a soft faced hammer and strike the sides of the oil pan until it begins to loosen from the block. You can then use a screwdriver/prybar to seperate the seal and have the pan come off

May 17, 2015 | 2005 Honda CRV 2.2

1 Answer

How to remove the oil pan on a 1996 honda accord


First you must remove the A exhaust pipe that is under the oil pan. Make sure use a penetrating lube, like WD-40 on all exhaust nuts. If there is a lot of rust, you can remove the 3 or 4 manifold nuts, the 2 bolts for the bracket to the block, and unhook the exhaust hangers, and move the whole exhaust out of the way. Drain the oil, then remove the support brackets, then all the 10mm oil pan bolts and nuts. The oil pan can seem glued in place, pry it loose without bending it. Make sure you get any steel rings off from around the studs, they are part of the oil pan gasket, and tend to stick to the block.

Oct 05, 2014 | 1996 Honda Accord

1 Answer

2006 HONDA PILOT OIL PAN REMOVAL


IS HARD TO DO THE JOB ON THE DRIVEWAY BUT I WILL GIVE YOU SOME DIRECTIONS.
DISCONNECT THE BATTERY
RISE THE VEHICLE AND DRAIN THE OIL
REMOVE THE EXHAUST PIPE FROM CAT.CONVERTER.
REMOVE THE SMALL CAP FROM TRANSMISSION LOWER SIDE COVERING THE FLEX PLATE.
REMOVE THE BOLTS FROM THE OIL PAN .
CLEAN THE GASKET FROM PAN AND ENGINE.
INSPECT THE OIL STRAINER AND CLEAN.
REPLACE THE GASKET AND INSTALL 4 BOLT TO FIX TO THE PAN IN POSITION.
INSTALL THE PAN AND DRIVE HALF WAY THE 4 BOLT.
INSTALL THE REST OF YOUR BOLTS AND TIGHT SLOWLY .
REPEAT IN 3 STEPS TIL TIGHT.
IF YOU SEE THE GASKET START TO BLOW OUT OF THE PAN, STOP. IF YOU OVER TIGHT WILL BRAKE THE GASKET AND WILL LEAK.
GOOD LUCK

Apr 23, 2014 | 2006 Honda Pilot

1 Answer

Oil pan


Replacing an Oil Pan Gasket
  • Drain oil through plug located at the bottom of oil pan.
  • Remove bolts around edge of the oil pan. There are probably around 8 of them.
  • Drop oil pan.
  • Clean gasket material from both block and oil pan.
  • Install new gasket.

Mar 12, 2010 | 1992 Honda Accord

1 Answer

How do I replace the oil pan gasket on a 2001 GMC Yukon XL?


Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.

Sep 15, 2009 | 2001 GMC Yukon

1 Answer

2000 chevy cavalier oil pan....2.2 lit....auto


put car on stands

remove right side engine splash shield

remove exhaust shield

remove AC brace at starter/ compressor bracket

remove flywheel inspection plate

remove engine mount strut, remove bolts from bracket. Lower the bracket slightly to gain clearance to remove pan.

remove oil filter extension (auto trans. only)

remove all pan bolts

tap pan with rubber hammer to break old gasket loose from block.

clean all used gasket off and install is reverse

Mar 13, 2009 | 2000 Chevrolet Cavalier

3 Answers

Oil Pan Gasket Replacement - How to - GMC Yukon 2000


No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 2000 GMC Yukon

1 Answer

1999 OIL PAN GASKET


you have to remove exhaust

Jan 05, 2009 | 1999 Honda CR-V

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...