Question about 1986 Ford Bronco II

1 Answer

86 ford bronco 2 no fire to the coil wires that plug into the coil so no fire

Bronco ran good now no fire to the coil.check for power to plug that goes to coil but no power to them.what could keep it from getting fire to the wires that plug into the coil.

Posted by on

  • david wagers Nov 04, 2012

    this is what i was also thinking it possibly was im picking up a ecu tomorrow for it and if that is not the problem will check for a break in the harness also.thanks for the help will let ya know how it goes later on today again thanks

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 1,007 Answers

This is either a wiring loom issue or a ECU issue.

Posted on Nov 04, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
cvstan
  • 40 Answers

SOURCE: what is the firing order for a 1984 ford bronco 2

1-4-2-5-3-6
Now you need to know which cylinder is which. If you stand at the front of the truck looking at the engine, the number 1 cylinder is on the left closest to you. The left bank has cylinders 1-3-5 and the right bank has 2-4-6. So number 1 is at the left front and number 6 is at the right rear.

Posted on Jan 25, 2010

warlock61
  • 659 Answers

SOURCE: spark plug wire diagram

1-5-4-2-6-3-7-8 counterclockwise

Posted on Jul 11, 2009

alicantecoli
  • 22326 Answers

SOURCE: 2001 ford windstar-new coil pack,new spark plugs

head gasket?? blowing between two cylinders

Posted on Mar 19, 2010

  • 834 Answers

SOURCE: 1966 ford f100 inline 6 cyl 300\r\engine turns

Make sure that the primary wire between the distributor ignition points and ignition coil is not damaged anywhere and grounding the circuit out. This is not a ground wire.

Replace the ignition points condenser, if this is shorted your points will never be able to work. With the condenser removed, use an ohm meter to check the resistance between the end of the condenser wire and the condenser caseing, there should be infinite resistance or an open loop, but it should not show any kind of a connection between the two, or it is grounded or "shorted to ground" and it will prevent the ignition system from working.

Are the ignition points adjusted properly? They have to open and close to send a dwell signal to the coil.

Connect a test light to ground and on the NEG. (-) side of the coil, have someone crank the engine and look for the test light to flash, the test light should flash indicating a dwell signal or coil pulse. (Do not use the POS. + side of the coil for this test, because you will not get a dwell signal).

If no dwell signal, then...

1. Turn off ignition and remove the distributor cap and turn the engine over until a high spot on the distributor cam lobe is on the rubbing block on the ignition points.

This is the fully open position for the ignition points and where they need to be to set them. and if you do not know the feeler gauge size, or the dwell angle to set your points at (according to manufacturers specifications), then tear off a piece of a match book and place it between the two point breakers.

2. Loosen the point hold down adjusting screw and move the base of the points with a screwdriver (look for adjusting nothches), until there is a light drag felt pulling on the match book. For the newer GM's up to 1974, just use a 1/8 allen wrench to obtain the same light drag on the match book.

3. Remove the matchbook and there should still be a small gap between the point breakers, rotate the engine and you should see the points open and fully close.

4. Pull the coil wire out of the distributor cap and ground the end of the coil wire well or you might get shocked.

5. Have someone crank the engine and re-check for a dwell signal, you should also see a blue-white spark flashing between the point breakers as they open and close.

If you now have a dwell signal then replace the distributor cap back onto the distributor and the the coil wire back onto the distributor cap, the engine should now start.

If you did not grease the rubbing block of the ignition points with die-electric grease when you installed them, then the rubbing block on the points will wear down prematurely, the points will close down, and the engine will no longer start.

If you crank your engine over and the ignition rotor turns clockwise (looking down at the rotor) then you need to put the die-electric grease along the right side of the rubbing block edge (looking down at the points) so that the grease is trapped between the points and the distributor cam lobe, and the distributor cam lobe can pick up the grease. (Grease the left side of the rubbing block edge if the ignition rotor turns counter-clockwise). Only use die-electric grease.

Posted on Apr 19, 2010

Rickygittins
  • 715 Answers

SOURCE: no power to fuel pump

check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down injectors and fuel pump, if you are looking for the shut off switch to reset the relay, it is on the passagers side floor board under the dash, gas two wires, orange and pink, I don't remember the color of the stripes, I removed this switch and wired them together without a problem

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coil wont fire all three wires have power but no fire to plugs replaced twice


Crank sensor if it has one,timing belt skipped is a possibility,and always the dread security key problem.don-ohio

Apr 01, 2013 | 2001 Ford Focus

1 Answer

Bronco II won't start


86 ford bronco 2 won't start changed coil wire acts like it wants to start not getting spark

Nov 10, 2012 | 1988 Ford Bronco II

3 Answers

96 bronco 5.8 cranks but no fire


Did you check primary voltage to ignition coil? red wire with lite green tracer, use a test lite to check voltage, goes hot with key on, circuit is fuse protected.

Dec 25, 2017 | Ford Bronco Cars & Trucks

1 Answer

I HAVE A 1995 FORD BRONCO EDDIE BAUER EDITION WITH THE 5.0L. I PUT NEW PLUGS FIRST, RAN FINE. THEN I PUT NEW CAP & ROTOR BUTTON, RAN FINE. THEN I PUT NEW WIRES ON AND WHERE THE WIRES GO ONTO THE PLUGS...


There is a technical bulletin isssued by ford in reference to the firing order on the 5.0 motors. I do not remember what cylinders they are but if you place certain wires running from certain cylinders they will arc and it is unpreventable. Try routing your wires a little different or taking the vehicle to ford, they should be aware of this issue.

Apr 03, 2010 | 1995 Ford Bronco

1 Answer

I have an 89 ford bronco 2 with a 2.9 liter it sat around for 2 years without being started. I replaced the plugs, rotor, cap, ran fuel injector cleaner through it several times, checked cylider...


check the spark plug wires are attached all the way till it snaps, pull each spark plugs, any black deposits on any plug means it isn't firing(faulty plug,or wire) last of all take off each injector wire and notice if there is a change in idle speed (plugged injector)

Mar 21, 2010 | 1989 Ford Bronco II

1 Answer

NOT GETTING FIRE IT CRANKS REAL GOOD BUT WONT FIRE


Check your coils and also check your spark plugs and plug wires.

Jan 02, 2010 | 1987 Ford Bronco II

1 Answer

Spark plug wire diagram


1-5-4-2-6-3-7-8 counterclockwise

Jul 11, 2009 | 1986 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...