Question about 2008 Hummer H3

Open Question

Installing ignition switch on 08 h3

How do i remove the old ignition switch to put in the new one ??

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to install a new wiper switch turn signal combo on a 1995 e-150 ford van and i need to know how to take out the old one and put in the new one correctly. Can you help me? Thanks, dan banes.


hey Dan, This is not to difficult if you have a tilt column drop it down by using the lever that's used to adjust it use a phillips screw driver and take out the screws that hold the plastic steering column shroud in place and remove the shroud you will also have to put the key in the ignition and turn it to the on position then using a long thin screw driver put it in the hole that you see under the ignition switch in the shroud and push the metal button in to remove the ignition cylinder and take the right side shroud off next unplug the connectors and unbolt the switch remove it and install the new one reverse removal and put the shroud back on this is for both tilt or stationary steering columns here's a photo of the switch to help you
need-install-new-wiper-switch-turn-h0yg5djg512bfyt30u0ootap-4-0.jpg

Nov 04, 2016 | Ford E-150 Cars & Trucks

2 Answers

H3 A/C Problems. New resistor...now what??


I had the same problem. I fix it my self. This is what you look for, is your a/c blower working when you turn the fan on. If a/c light come on but nut the blower fan. Then under passenger dash you will see orange plug. It's held in with 2 screws. Remove 2 screws and pull resistor out. Disconnect orange plug and look at orange plug and the resistor if burn need to replace the resistor and the orange connector. That's your problem. Now if your blower works but no power to a/c switch and you instrument nobles has no lights. Then it's a fuse check #48 and # 57 fuse that controls that Troy

Mar 28, 2012 | 2008 Hummer H3

1 Answer

How to remove a ignition switch on a 1988 ford mustag LX fox body 5.0L


Disconnect your negative battery terminal, then remove the plastic from around the steering column (3 screws), then turn the the ignition lock cylinder to run position, then directly down from the lock cylinder is the ignition switch, remove the two security screws and unplug the old ignition, plug in the new ignition switch, install the security screws, put plastic back on column. Put negative cable back on, DONE.

Feb 27, 2011 | Ford Mustang Cars & Trucks

1 Answer

How to install ignition switch


follow these instructions:

Removing the Old Ignition Switch
1.

Remove the steering wheel housing. This will be held on by two screws. One will be in the front and the other will be in the back of the housing. The screws are usually Phillips heads or star-shaped heads.
2.

Locate the switch behind behind the key tumbler. It will be held by a screw.
3.

Remove the screw holding in the switch. The switch will work its way loose.
4.

Unattach the pigtail attached to the back of the ignition switch. They should lock in with a tab that needs to be folded up so the pigtail can be slid out.
5.

Remove the old switch. It will slide right out.

Installing the Ignition Switch
1.

Install the new switch. Inspect to make sure it looks like the old one.
2.

Plug the wiring into the back of the switch. The wiring pigtail will lock into place.
3.

Screw the switch back into position where the old one was removed. The new switch should sit in the same as the old one.
4.

Place the steering column housing back around the steering wheel. Install it as you took it off. The housing is set to fit around the column and fits one way.
5.

Tighten the screws on the housing. The housing should be snug.

Feb 06, 2011 | 2005 Chevrolet Uplander

1 Answer

I have 08 Hummer H3 3.7 and show code P300 ! but get new plugs crank,cam and alternator i found one problem whit the alternator , start 14.8V charging and gos to 12.3V after 5 minutes ! i see some battery...


I AM LOOKING AT ALTERNATOR.IF ITS FAULTY.IT WILL CAUSE PCM PROBLEMS AND MISFIRE TO ALL CYLINDERS DUE TO WEAK SPARK TO IGNITION SYSTEM. CHECK YOUR WARRANTY THEY MIGHT FIX IT.STILL A NEW VECHICLE.

Jun 18, 2010 | 2009 Hummer H3

1 Answer

Door jar error light will not go off even after opening and closing all the doors. It started when i opened the back hatch door Have an 08 H3 alpha


You need to locate the rear door hatch switch and free it up or replace it if that is not an option.Merry Christmas and good luck!

Dec 24, 2009 | 2008 Hummer H3

2 Answers

Need to change the ignition switch


Remove panel under steering wheel. Put key in cylinder and turn back to accessory position. Looking under lower part of steering column locate a small pin under the key cylinder. While depressing the pin turn the key backwards and pull the entire cylinder with key out of column. Good luck.

Apr 25, 2009 | 1990 Ford Econoline

1 Answer

How to remove old ignition switch and install the new one


on ignition cylinder shaft/housing there is a recessed button in it put key in ignition push on button then turn key to on position u will feel button sink in then pull cylinder out

Mar 21, 2009 | 1995 Toyota Camry

3 Answers

2009 Hummer h3 won't start


I can't get my hummer to start! put in a nwe battery and starter and it still will not crank!........ when I turn the key I get nothing.......

1 could it be the init.switch
2 or some other issue

Dec 29, 2008 | 2006 Hummer H3

1 Answer

Heating up


This may be normal, depending on the thermostat installed. They make optional thermostats of various temps. You can probably get a 190 degree thermostat. It will probably not have a significant effect on the engine operation, but may give you some peace of mind.

Aug 24, 2017 | 2006 Hummer H3

Not finding what you are looking for?
2008 Hummer H3 Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...