Question about 2005 Dodge Durango Limited

Open Question

Remote on my VES system does not work - 2005 Dodge Durango Limited

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 Buick Lacrosse suddenly started pulling to the right and became very hard to steer. Then the "Charging System Failure" warning came on. What could this be?


Do you know if your vehicle has --------------------------------------------------------------------------------
Power Steering System (w/o Electro-Hydraulic Steering) or
Variable Effort Steering System
The variable effort steering (VES) system or MAGNASTEER® varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking maneuvers. Steering effort is increased at higher speeds to provide firmer steering for increased road feel and directional stability. The electronic brake control module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and set a DTC.
Are there any other lights lit on the dash ? ABS ?
DTC C0450 Steering Assist Control Solenoid/Motor/Actuator Circuit could have a diagnostic trouble code !
The electronic brake control module (EBCM) commands current from 0-1 amp to the variable effort steering (VES) actuator, depending on vehicle speed. At low speeds, 1 amp of current is commanded to the actuator and the actuator valve is fully closed. A speed increases, less current is commanded to the actuator and the valve opens, allowing pressure to bleed off through a power steering fluid orifice. The EBCM monitors and compares the Commanded and Feedback Current parameters to detect malfunctions in the VES system.
Or you could have a bad steering rack !
Charging System/Generator Fault
Refer to Charging System Description and Operation in Engine Electrical
Alternator problem maybe !
The electrical power management (EPM) system is designed to monitor and control the charging system and send diagnostic messages to alert the driver of possible problems with the battery and generator. This EPM system primarily utilizes existing on-board computer capability to maximize the effectiveness of the generator, to manage the load, improve battery state-of-charge (SOC) and life, and minimize the system's impact on fuel economy. The EPM system performs 3 basic functions:
• It monitors the battery voltage and estimates the battery condition.
• It takes corrective actions by adjusting the regulated voltage.
• It performs diagnostics and driver notification.

Nov 27, 2016 | Buick Cars & Trucks

2 Answers

I just put hub bearings on my 2005 grand Prix GTP and when I plug the sensor it says service variable effort steering what's wrong.


check the sensor on top of the steering rack ,their is a sensor that increases the idle when the steering is turned when the vehicle is stationary

Nov 10, 2016 | Cars & Trucks

2 Answers

What is wrong with this 2007 pontiac g/p no p/s at low rpms?


The power steering pump has nothing to do with it .
Variable Effort Steering System Description and Operation
The Variable Effort Steering (VES) system or MAGNASTEER?® Varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking Maneuvers. Steering effort is increased at higher speeds to provide firmer steering (road feel) and directional stability. The Electronic Brake Control Module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and setting a DTC.
Your best bet is take your vehicle to a GM dealer or a ASE certified repair shop that knows about this system .

Mar 14, 2016 | 2007 Pontiac Grand Prix

1 Answer

Were is the steering pump sensor on pontiac grand prix gt 2005


This is a very complex system an if you don't work on these systems all the time , I suggest you take it to a ASE certified repair shop that does !
The Variable Effort Steering (VES) system or MAGNASTEER?® Varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking Maneuvers. Steering effort is increased at higher speeds to provide firmer steering (road feel) and directional stability. The Electronic Brake Control Module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and setting a DTC - diagnostic trouble code !

Sep 29, 2015 | Pontiac Grand Prix Cars & Trucks

1 Answer

2007 Pontiac Grand prix GT steering components diagram


Variable Effort Steering System Description and Operation
The Variable Effort Steering (VES) system or MAGNASTEER® Varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking Maneuvers. Steering effort is increased at higher speeds to provide firmer steering (road feel) and directional stability. The Electronic Brake Control Module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and setting a DTC.

The Magnasteer® system is a speed-dependent power steering system. The Magnasteer® system provides power assist at varying levels depending on need.
A bi-directional magnetic rotary actuator in the steering gear adjusts the amount of torque (driver effort) necessary to turn the steering wheel.
The Magnasteer® is controlled through the ABS module and varies the torque by adjusting the current flow through the actuator.
The amount of adjustment will be directly related to the vehicle speed. The controller receives speed-related input signals from the vehicle speed sensor.
For more information on Magnasteer® refer to Variable Effort Steering System Description and Operation

Is the vehicle driveable ? The steering wheel is connected to the wheels

DTC C0450 Steering Assist Control Solenoid/Motor/Actuator Circuit
Sounds like it's stuck on full assist .

Apr 25, 2017 | Cars & Trucks

1 Answer

Repair flipdown monitor on 2008 town and country


Town and Country, Grand Caravan, and Routan are all having this same problem with the VES. 2nd row screen is blank and 3rd row screen shows split screen with no signal. Here is the fix.
http://www.youtube.com/watch?v=4jBndxy8rpg
Get the cable from here.
http://www.ebay.com/itm/2008-2009-2010-2011-2012-Routan-Caravan-Town-Country-VES-2nd-row-Monitor-Fix-DIY-/151057952865?pt=Car_Audio_Video&hash=item232bc17061&vxp=mtr

Jun 29, 2012 | 2008 Chrysler Town & Country

2 Answers

Why i have to refil the radiator water evry 2 wks. i just change also the termostad and temperature sames ok. no leaking any ware...


Check the condition of the seals in the radiator cap, the coupling hose to the overflow tank, and the tank itself for any cracks. Make sure that water isn't ending up in your oil supply. You might have head gasket problems that allow combustion gases into the cooling system forcing out water and causing overheating. A well-equipped shop will have a test for that problem and can advise on repairs. Good luck!

Nov 18, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
2005 Dodge Durango Limited Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...