Question about 1991 Honda Accord

1 Answer

REMOVING ALTERNATOR CANT SEEM TO GET IT FULLY LOOSENED---IS THERE A BOLT ON BOTTOM SIDE OR IS A PIN YOU DRIVE OUT--OR DO U HAVE TO REMOVE FULL BRACKET ASSEMBLY--ANY HELP WOULD BE APPRECIATED TKS!!! DAVE

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

Its just a bolt on the top and one on the bottom and the adjuster its has a long 10mm bolt an a 12mm nut on it, the top bolt is a ling 14mm bolt. Here is a diagram Good Luck, thanks for using FIX YA. http://www.2carpros.com/car_repair_information/tec_info/1991/honda/accord/1991_honda_accord_drive_belt_routing_diagram.htm

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Where is alternator located in the engine compartment?


Are these guys SERIOUS??


blueextc3221_1.jpg

The alternator is accessed from UNDER the vehicle LEFT SIDE facing the engine bay.

REMOVAL & INSTALLATION




1. Disconnect the negative battery cable.

2. Loosen, but do not remove the alternator adjusting nut.

3. Turn the front wheels completely to the right, then raise and safely support the vehicle.

4. Unfasten the retainers, then remove the plastic lower splash shield.

5. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.

6. Remove the B+ terminal nut and wire.

7. Loosen the alternator pivot bolt, but do not remove it.

8. Remove the alternator drive belt. The alternator spill shield does not have to be removed.

9. If necessary, remove the bottom pivot bolt and anti-rotation tab.

10. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.

11. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.

12. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.

13. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.

14. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).

15. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.

16. Install the alternator drive belt.

17. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).

18. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).

19. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.

20. Install the splash shield, then carefully lower the vehicle.

21. Tighten the adjusting nut.

22. Connect the negative battery cable. Adjust the alternator belt.

Thanks!!

Feb 07, 2011 | 1998 Dodge Neon

1 Answer

Changing alternator



REMOVAL & INSTALLATION 2.2L Engines
CHRYSLER ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.

When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.
To install:
  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.

To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

Jan 02, 2011 | 1994 Plymouth Voyager

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

2 Answers

How do you install the alternator


1990-93 Accord
  1. With the ignition OFF, disconnect the negative battery cable.
  2. Remove the power steering pump. Refer to Section 8 for the complete procedure.
  3. Remove the cruise control actuator but do not disconnect the actuator cable; simply move the unit out of the way with the cable attached.
  4. Unplug the multi-pin electrical connector.
  5. Remove the terminal nut and remove the wire from the terminal.
  6. Loosen the adjusting bolt; remove the alternator nut. Fig. 3: Alternator mounting on 1990-93 Accords 86803003.gif

  7. Remove the belt from the alternator pulley.
  8. Remove the adjusting bolt, the lower through-bolt and the small support stay.
  9. Support the alternator. Remove the upper through-bolt and remove the alternator.
  10. If desired, remove the alternator mounting brackets. To install:
  11. If the alternator brackets were removed, reinstall them. Coat the bolts with a thread sealer or liquid thread lock. Install the bracket bolts and tighten them to 36 ft. lbs. (50 Nm).
  12. Fit the alternator into place. Install the upper through-bolt and tighten it to 33 ft. lbs. (45 Nm).
  13. Install the small stay, the lower through-bolt and the adjusting bolt. Make certain the adjusting bolt is properly installed.
  14. Install the belt. Install the alternator nut. Adjust the belt tension. Tighten the alternator nut to 19 ft. lbs. (26 Nm).
  15. Connect the wire to the terminal and tighten the nut.
  16. Engage the multi-pin connector to the alternator.
  17. Install the cruise control actuator.
  18. Install the power steering pump.
  19. Connect the negative battery cable.

Oct 18, 2010 | 1992 Honda Accord

1 Answer

How do you take the alternator off for a 96 plymouth neon


For REMOVAL & INSTALLATION check this procedure...
  1. Disconnect the negative battery cable.
  1. Loosen, but do not remove the alternator adjusting nut.
  1. Turn the front wheels completely to the right, then raise and safely support the vehicle.
  2. Unfasten the retainers, then remove the plastic lower splash shield.
  1. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.
  1. Remove the B+ terminal nut and wire.
  1. Loosen the alternator pivot bolt, but do not remove it.
  1. Remove the alternator drive belt. The alternator spill shield does not have to be removed.
  1. If necessary, remove the bottom pivot bolt and anti-rotation tab.
  1. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.
  2. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.
To install:
  1. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.
  2. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.
  3. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  4. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.
  5. Install the alternator drive belt.
  6. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).
  7. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).
  8. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.
  9. Install the splash shield, then carefully lower the vehicle.
  10. Tighten the adjusting nut.
  11. Connect the negative battery cable. Adjust the alternator belt.

Hope helps.

Jul 16, 2010 | 1996 Plymouth Neon

2 Answers

Alternator Removal


Alternator - REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Remove the passenger side engine and transaxle splash shield.
  4. Remove the alternator wiring harness bracket bolt from the rear of the alternator.
  5. Disconnect the alternator electrical connector from the alternator.
  6. Remove the ground wire nut and wire.
  7. Remove the B terminal wire boot. Remove the B terminal nut and wire.
  8. Loosen the inner and outer alternator to bracket mounting bolts.
  9. Loosen the alternator adjustment lock bolt.
  10. Turn the alternator adjustment bolt counterclockwise to loosen the belt.
  11. Remove the belt from the alternator.
  12. Remove the alternator lock bolt and washer.
  13. Remove the inner alternator to bracket mounting bolt and two washers.
  14. Remove the outer alternator to bracket mounting bolt and two washers.
  15. Remove the alternator.
  16. The installation is the reverse of removal.
  17. Adjust the drive belt. For the procedure, please refer to General Information and Maintenance, Routine Maintenance and Tune-Up, Belts, Adjustment, Alternator.
cf55885.jpg

Fig. Alternator wire identification


Hope help with this (remember rated this post).


May 17, 2010 | 1998 Mercury Villager

1 Answer

How to remove alternator from 1997 Chrysler Concorde?


e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1997 Chrysler Concorde

2 Answers

I need to find out how to remove the alternator from my 2002 Kia Spectra


The steps to replace an alternator are:
  1. Do the following through the passenger side of the engine bay of course with the hood up.
  2. First and most important is to disconnect the negative connection to the battery (driver side).
  3. Using a 12mm socket loosen the tension adjusting screw and bracket screw. Using a 10mm socket or open end remove wirings. Pinched other connector to remove.
  4. Using 14mm socket with 3/8 drive ratchet remove the big bolt on the lower side of the alternator.
  5. You might need some help from a pipe for extra leverage.
  6. Remove all parts that will hinder the removal of the alternator.For example the charcoal cannister on the firewall just slide up.
  7. Ease the alternator through the opening by turning the alternator untile it can pass through the opening.

Sep 19, 2009 | 2002 Kia Spectra

2 Answers

Bad alternator


Disconnect the negative clamp on the battery. Remove the bolt on the adjustment arm (the one with the slot) of the alternator. Loosen the pivot bolt at the bottom of the Alt. Swing the alt inward to loosen the belt. Take the belt of the pulley. Take off the wires noting where they attach. Remove the pivot bolt. You should be able to take the alt off now. Reverse the sequence but when adjusting the belt tension pry the side of the alternator with a bar so the belt can only be deflected about three quarters of an inch. Tighten the adjustment bolt. Don't over tighten the belt. It'll prematurely wear your bearings. Don't under tighten. It'll squeal.

May 08, 2009 | Ford Explorer Cars & Trucks

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...